Warnungen
Auf dieser Webseite wird die Software von Geräten aufgeführt, die das OpenWrt-System unterstützen. Bitte beachten Sie vor dem Herunterladen und Installieren der Software, dass es sich bei OpenWrt Project um ein Linux-Betriebssystem für eingebettete Geräte handelt. Anstatt zu versuchen, eine einzelne, statische Firmware zu erstellen, bietet OpenWrt ein vollständig beschreibbares Dateisystem mit Paketverwaltung. Dies befreit Sie von der vom Anbieter bereitgestellten Anwendungsauswahl und -konfiguration und ermöglicht Ihnen, das Gerät durch die Verwendung von Paketen an jede Anwendung anzupassen. Für Entwickler ist OpenWrt das Framework zum Erstellen einer Anwendung, ohne eine komplette Firmware darum herum erstellen zu müssen; Für Benutzer bedeutet dies die Möglichkeit einer vollständigen Anpassung, um das Gerät auf eine Art und Weise zu nutzen, die nie vorstellbar war.
Beschreibung
- Diese Datei kann nur verwendet werden, wenn Ihr Router unter der Cudy-Web-Benutzeroberfläche funktioniert.
- Wenn der Router bereits unter der OpenWRT-Benutzeroberfläche funktioniert, sollte der Benutzer ihn zuerst auf die offizielle Cudy-Firmware wiederherstellen. Und aktualisieren Sie dann den Router mit dieser Firmware.
- Wie kann ich den Router auf die offizielle Firmware von Cudy zurücksetzen? Bitte lesen Sie die Readme-Datei in der heruntergeladenen Datei.
Garantie:
Cudy erklärt hiermit
- Wir, Cudy, übernehmen keine Garantie für Software, die nicht von Shenzhen Cudy Technology Co., Ltd. veröffentlicht wurde.
- Wir übernehmen keine Garantie für Produkte, auf denen Software installiert ist, die nicht von Shenzhen Cudy Technology Co., Ltd. freigegeben wurde.
- Wenn Sie OpenWRT-Software verwenden müssen, empfehlen wir Ihnen, diese von der offiziellen Website von Cudy herunterzuladen.
Laden Sie die OpenWrt-Firmware herunter, um die Signaturprüfung zu entfernen: Drive
OpenWrt Firmware Finder (nicht von Cudy veröffentlicht): OpenWrt-Firmware-Auswahl
1019 Kommentare
@Dear Michael,
Regarding the tftpd recovering firmware method. You can refer to this article.
https://www.cudy.com/blogs/faq/how-to-recovery-the-cudy-router-from-openwrt-firmware-to-cudy-official-firmware?pos=1&_sid=b98054b19&ss=r
You can download the firmware for you router via this link.
https://www.cudy.com/pages/download-center/wr3000-1-0
“Hello Cudy Support Team ,
Maybe you have some intermediate , temporary firmware ,that I can flash to my WR3000 v1 using tftp64 so it will restore it’s state to defaults ? with memory erasing and rebuilidng the filesystem ? Thaks in advance.”
Hello Cudy Support Team ,
Maybe you have some intermediate , temporary firmware ,that I can flash to my WR3000 v1 using tftp64 so it will restore it’s state to defaults ? with memory erasing and rebuilidng the filesystem ? Thaks in advance.
“@Dear Michael,
I see. I suggest you can try to do it by yourself. We don’t have such instructions.
“Hi Cudy Support Team , I’ve tried what you suggested – flashing older official firmware, but no luck , my Cudy WR3000 v1 is still bootlooping. Is there any firmware or recovery steps that I might perform in order to recover my router so I be able to boot into GUI ?
One more note : after flashing your firmware from Google drive or OpenWRT firmware, I’m able to enter to OpenWRT failsafe mode and access router via LAN using SSH , but from there I wasn’t able to perform system restoration steps from OpenWRT guides( I just don’t know how to do it propertly) . Thanks is advice for your support.
@Dear Support
I have already built a working OpenWrt firmware for AP1300 v1.0, based on the OpenWrt firmware for AP1300 Outdoor v1.0 (same SoC and hardware platform).
The firmware itself builds and boots, but I cannot flash it via TFTP or the web interface because the stock firmware requires a signed image.
To proceed without hardware modification (UART/SPI), I need an intermediate firmware that can be installed via the web interface and allows upgrading to a custom OpenWrt image (without signature verification).
Could you please provide such an intermediate firmware for AP1300 v1.0, or advise if there is an official way to bypass the signature check for development purposes?
Thank you.
“@Dear Bourn,
There is no OpenWrt firmware for AP1300 V1.0 currently. The OpenWrt firmware is not developed by Cudy but by the developers. We need the OpenWrt forum official support the router at first, then we can release a middle firmware for you, then you can use and upgrade to the OpenWrt firmware. "
@Dear Michael,
I see. I suggest you can try to do it by yourself. We don’t have such instructions.
“Hi Cudy Support Team , I’ve tried what you suggested – flashing older official firmware, but no luck , my Cudy WR3000 v1 is still bootlooping. Is there any firmware or recovery steps that I might perform in order to recover my router so I be able to boot into GUI ?
One more note : after flashing your firmware from Google drive or OpenWRT firmware, I’m able to enter to OpenWRT failsafe mode and access router via LAN using SSH , but from there I wasn’t able to perform system restoration steps from OpenWRT guides( I just don’t know how to do it propertly) . Thanks is advice for your support.”
@Dear A,
Our technical support has contacted you via email. Please check.
“WR3000P2550 . Can’t change to intermdiate cudy_wr3000p-v1-sysupgrade_20251119.bin: “File is invalid. Please retry.”
is it possible to get openwrt for WR3000P with new serial number?”