警告
本網頁列出了支援OpenWrt系統的設備的軟體，在下載和安裝軟體之前，請注意OpenWrt Project是一個針對嵌入式設備的Linux作業系統。 OpenWrt 並沒有嘗試建立單一靜態韌體，而是提供了一個具有套件管理功能的完全可寫入檔案系統。這使您無需選擇供應商提供的應用程式和配置，並允許您透過使用軟體包來自訂設備以適應任何應用程式。對於開發人員來說，OpenWrt 是建立應用程式的框架，而無需圍繞它建立完整的韌體；對使用者來說，這意味著完全客製化的能力，以前所未有的方式使用裝置。
描述
- 此檔案僅當您的路由器在 Cudy Web UI 下運作時才能使用。
- 如果路由器已經在OpenWRT UI下工作，用戶應先將其恢復到Cudy官方韌體。然後用這個韌體升級路由器。
- 如何將路由器恢復至Cudy官方韌體？請閱讀下載文件中的自述文件。
保固：
Cudy特此聲明
- 我們 Cudy 對非深圳市 Cudy 科技有限公司發布的任何軟體不承擔任何保證。
- 對於安裝了非深圳市酷迪科技有限公司發布的任何軟體的產品，我們不承擔任何保證。
- 如果您需要使用openwrt軟體，建議您從Cudy官網下載。
下載 OpenWrt 韌體以刪除簽名檢查：驅動程式
OpenWrt 韌體查找器（不是由Cudy 發布）：OpenWrt 韌體選擇器
1530 則留言
@Dear ABDUL,
Sorry, there is no wr1200 v2.1 open wrt firmware currently. The OpenWrt firmware is not developed by Cudy but by the developers. We need the OpenWrt forum official support the router at first, then we can release a middle firmware for you, then you can use and upgrade to the OpenWrt firmware.
“I need cudy wr1200 v2.1 open wrt firmware”
“I need cudy wr1200 v2.1 open wrt firmware”
@Dear Moritz,
Our technical support has sent you the firmware via email. Please check.
“Dear Cudy Team
I have not seen an intermediate FW for the “AP1200 Outdoor 1.0” in the google drive link provided. Is it possible to install OpenWRT on this one? (I tried using RE1200, TR1200 and AP1300 but without success)
Thanks
Moritz”
I need cudy wr1200 v2.1 open wrt firmware
Dear Cudy Team
I have not seen an intermediate FW for the “AP1200 Outdoor 1.0” in the google drive link provided. Is it possible to install OpenWRT on this one? (I tried using RE1200, TR1200 and AP1300 but without success)
Thanks
Moritz
@Dear Alex,
Our technical support has contacted you via email. Please check.
“Hello!
Checked and recheched, manual “How to made a brick from Cudy M1800 EU2.0”:
Flash AP with an Openwrt image from page (https://www.cudy.com/en-us/blogs/faq/openwrt-software-download) for example M1800+V2.zip
Update AP with actual Openwrt image (https://firmware-selector.openwrt.org/?version=25.12.6&target=ramips%2Fmt7621&id=cudy_m1800) – sysupgrade
3. All works OK.
Try to recover with official manual (https://www.cudy.com/en-us/blogs/faq/how-to-recovery-the-cudy-router-from-openwrt-firmware-to-cudy-official-firmware) with an image from stage1.
AP reloads with Cudy FW and a error “Invalid board info!”.
Reflash Cudy FW – nothing changed.
Flash openwrt image from stage1 – AP reloaded, but web is not accessible.
Reflash openwrt from stage1 – AP NOT reloaded, led lights slightly, NO UART! GREAT! We got a brick!
Official instruction is bad. Please send me full-flash image to program via flasher or recovery! If it’s needed i can give serials.
Thank you!"