警告
本網頁列出了支援OpenWrt系統的設備的軟體，在下載和安裝軟體之前，請注意OpenWrt Project是一個針對嵌入式設備的Linux作業系統。 OpenWrt 並沒有嘗試建立單一靜態韌體，而是提供了一個具有套件管理功能的完全可寫入檔案系統。這使您無需選擇供應商提供的應用程式和配置，並允許您透過使用軟體包來自訂設備以適應任何應用程式。對於開發人員來說，OpenWrt 是建立應用程式的框架，而無需圍繞它建立完整的韌體；對使用者來說，這意味著完全客製化的能力，以前所未有的方式使用裝置。
描述
- 此檔案僅當您的路由器在 Cudy Web UI 下運作時才能使用。
- 如果路由器已經在OpenWRT UI下工作，用戶應先將其恢復到Cudy官方韌體。然後用這個韌體升級路由器。
- 如何將路由器恢復至Cudy官方韌體？請閱讀下載文件中的自述文件。
保固：
Cudy特此聲明
- 我們 Cudy 對非深圳市 Cudy 科技有限公司發布的任何軟體不承擔任何保證。
- 對於安裝了非深圳市酷迪科技有限公司發布的任何軟體的產品，我們不承擔任何保證。
- 如果您需要使用openwrt軟體，建議您從Cudy官網下載。
下載 OpenWrt 韌體以刪除簽名檢查：驅動程式
OpenWrt 韌體查找器（不是由Cudy 發布）：OpenWrt 韌體選擇器
1319 則留言
@Dear araujorm,
Our technical support has sent you the firmware via email. Please check.
“Hi. It’s been a few weeks since I’ve sent Cudy via email a Openwrt image that should be suitable for RE1800 V2, and also shared the link to the github repository for it, asking if you could sign it so that I can finish providing support for it along with the Opewrt team. After an initial reply asking to wait, I got no other replies. Could you please take a look into it?”
@Dear Viktor (tg: OriginWave),
Our technical support has sent you the firmware via email. Please check.
“Hello Cudy Support Team,
I have a Cudy WR3000 v1.0 router.
Serial Number starts with 2549
I would like to install OpenWrt on my router. Could you please provide the Cudy-signed intermediate firmware compatible with my hardware revision?
Thank you.”
@Уважаемая Никита,
Прошивки OpenWrt для WR1300 v4 не существует.
“Здравствуйте, поддерживает ли Cudy WR1300 v4 OpenWrt? Я нашел промежуточную прошивку на гугл диске для v4, но не нашел прошивку OpenWrt для v4.”
@Dear Lukas,
Our technical support has contacted you via email. Please check.
“Hello,
I have a Cudy WR3000 v1.0 router.
Serial number starts with: 2517
Current stock firmware: 2.4.19-20250828-192837
I downloaded the package:
“WR3000+V1 without recovery TFTP”
However, the package only contains:
- openwrt-mediatek-filogic-cudy_wr3000-v1-sysupgrade.bin
The stock Cudy firmware rejects this file with an error during firmware upgrade.
From the OpenWrt installation instructions, it seems that a signed intermediate firmware or factory image is required before installing OpenWrt.
Could you please provide the correct intermediate firmware for WR3000 v1.0 compatible with the latest stock firmware?
Thank you."
@Dear Leo,
We don’t change the Flash chip on WR3000 1.0. Please just use the intermediate firmware “WR3000 v1 without recovery TFTP” .
“Hello!
Device: Cudy WR3000 v1.0
Serial Number: 2553…
Stock firmware version: 2.4.19-20250828-192837
The publicly available intermediate firmware in your Google Drive folder
“WR3000 v1 without recovery TFTP” is incompatible with the new F50L1G41LC
flash chip used in units manufactured from week 43 of 2025 onward.
Could you please email me the updated Cudy-signed intermediate firmware
for the WR3000 v1.0 with the new flash chip?
Thank you!"