Avvertenze
Questa pagina web elenca il software dei dispositivi che supportano il sistema OpenWrt. Prima di scaricare e installare il software, tieni presente che OpenWrt Project è un sistema operativo Linux destinato ai dispositivi incorporati. Invece di provare a creare un singolo firmware statico, OpenWrt fornisce un filesystem completamente scrivibile con gestione dei pacchetti. Ciò ti libera dalla selezione e configurazione dell'applicazione fornita dal fornitore e ti consente di personalizzare il dispositivo attraverso l'uso di pacchetti adatti a qualsiasi applicazione. Per gli sviluppatori, OpenWrt è il framework per creare un'applicazione senza dover costruire attorno ad essa un firmware completo; per gli utenti questo significa la possibilità di personalizzazione completa, di utilizzare il dispositivo in modi mai immaginati.
Descrizione
- Questo file può essere utilizzato solo quando il router funziona con l'interfaccia utente web di Cudy.
- Se il router funziona già con l'interfaccia utente OpenWRT, l'utente deve prima ripristinarlo sul firmware ufficiale Cudy. E poi aggiorna il router con questo firmware.
- Come ripristinare il router sul firmware ufficiale Cudy? Si prega di leggere il file Leggimi nel file scaricato.
Garanzia:
Cudy dichiara
- Noi, Cudy, non ci assumiamo alcuna garanzia per alcun software che non sia rilasciato da Shenzhen Cudy Technology Co., Ltd.
- Non assumiamo alcuna garanzia per i prodotti che hanno installato software non rilasciato da Shenzhen Cudy Technology Co., Ltd.
- Se hai bisogno di utilizzare il software openwrt, ti suggeriamo di scaricarlo dal sito Web ufficiale di Cudy.
Scarica il firmware OpenWrt per rimuovere il controllo della firma: Drive
Ricerca firmware OpenWrt (non rilasciato da Cudy): Selettore firmware OpenWrt
1530 commenti
Hello.
I have a Cudy WR3000H V1.0.
Serial number: S0001004261801871
Current stock firmware: 2.4.5-20250515-105059
I would like to install the latest official OpenWrt.
Please send me the latest Cudy-signed OpenWrt intermediate firmware compatible with my WR3000H V1.0 and the new Flash revision.
Thank you.
Hello Cudy Support,
I have a Cudy M3000 v2.0 (board R37) with Motorcomm YT8821 WAN PHY and ESMT F50L1G41LC SPI NAND. It is currently running stock firmware 2.4.19-20250828.
I want to install official OpenWrt 25.12.5. The M3000 1.0_2.0.zip archive contains cudy_m3000-v1-sysupgrade__20251119.bin, but this image refers to rtl8221b_phy, while my router has YT8821.
Could you please email me a Cudy-signed intermediate firmware confirmed to support this exact hardware combination? Please also confirm which OpenWrt image I should install afterward and provide the installation steps. I have not flashed the router yet.
Thank you!
Hello Cudy Support,
I have sent you this message as an email too.
My WR300 v1 bootloops after flashing the official OpenWrt intermediate
firmware (openwrt-ramips-mt76x8-cudy_wr300-squashfs-flash.bin). Stock firmware 2.5.24 works fine on this unit; the bootloop only starts after installing the
intermediate.
Serial number: S0000759261510557
Board marked as: 300100157 REV1.1
flash: cFeon QX64A-104HIP
Cause (from the UART boot log): this unit doesn’t recognize the flash chip
(JEDEC ID 1c 71 17). Newest firmware’s U-Boot recognizes it as `en25qx64a`,
but the kernel inside the intermediate (5.15.167, Sep 2024) has no driver
entry for it:
```
[ 0.350812] spi-nor spi0.0: unrecognized JEDEC id bytes: 1c 71 17 1c 71
17
[ 0.357913] spi-nor: probe of spi0.0 failed with error -2
…
[ 0.471677] Kernel panic – not syncing: VFS: Unable to mount root fs on
unknown-block(0,0)
```
Flashing the intermediate through tftp recovery also downgrades the
bootloader to an older U-Boot (Feb 11 2025) that prints
```
flash manufacture id: 1c, device id 71 17
Warning: un-recognized chip ID, please update bootloader!
```
Additionally, the TFTP recovery appears to only accept Cudy-signed images – an unsigned OpenWrt image passes the “R54” name check but is never flashed
(no “flash image / rsa verify” lines). So I could not install a patched
OpenWrt build myself;
I restored the router with the stock firmware via TFTP recovery and it
works again.
Could you please provide an updated intermediate firmware whose kernel
supports the EN25QX64A (1c 71 17)? A similar issue was fixed for the AX3000
series after its flash chip change.
Also, would you consider disabling RSA verification in the U-Boot TFTP
recovery, and/or providing a way to interrupt the U-Boot boot sequence to
reach a serial console? Otherwise an spi programmer adapter is required (like ch341a).
Thank you
Hello Cudy Support Team,
I have a Cudy WR3000 V1.0 (EU 1.0).
Current stock firmware:
2.4.19-20250828-192837
Serial number:
WR3000243506896
I would like to install official OpenWrt.
Please provide the latest Cudy-signed OpenWrt intermediate firmware compatible with my WR3000 V1.0 and my flash memory revision.
Thank you.
Hi, I have a Cudy WR3000 EU 1.0 router with serial number starting with 2451 running firmware 2.2.6 US. I would like to install OpenWRT. Can you provide me the intermediate firmware for my device?
By the way, is there any reason not to have it available in the Google Drive folder along with the other models?