警告
本網頁列出了支援OpenWrt系統的設備的軟體，在下載和安裝軟體之前，請注意OpenWrt Project是一個針對嵌入式設備的Linux作業系統。 OpenWrt 並沒有嘗試建立單一靜態韌體，而是提供了一個具有套件管理功能的完全可寫入檔案系統。這使您無需選擇供應商提供的應用程式和配置，並允許您透過使用軟體包來自訂設備以適應任何應用程式。對於開發人員來說，OpenWrt 是建立應用程式的框架，而無需圍繞它建立完整的韌體；對使用者來說，這意味著完全客製化的能力，以前所未有的方式使用裝置。
描述
- 此檔案僅當您的路由器在 Cudy Web UI 下運作時才能使用。
- 如果路由器已經在OpenWRT UI下工作，用戶應先將其恢復到Cudy官方韌體。然後用這個韌體升級路由器。
- 如何將路由器恢復至Cudy官方韌體？請閱讀下載文件中的自述文件。
保固：
Cudy特此聲明
- 我們 Cudy 對非深圳市 Cudy 科技有限公司發布的任何軟體不承擔任何保證。
- 對於安裝了非深圳市酷迪科技有限公司發布的任何軟體的產品，我們不承擔任何保證。
- 如果您需要使用openwrt軟體，建議您從Cudy官網下載。
下載 OpenWrt 韌體以刪除簽名檢查：驅動程式
OpenWrt 韌體查找器（不是由Cudy 發布）：OpenWrt 韌體選擇器
1319 則留言
Dear Cudy Support Team,
I desperately need your assistance with my bricked WR3000E router. Here is the complete situation:
Device Details:
Model: Cudy WR3000E
Hardware Version: v1.0
Original Firmware: 2.2.6-20240902-033948
What I have done:
Downloaded official firmware WR3000E-R53-2.4.7-20250528-182254-sysupgrade.zip from your website
Renamed it to recovery.bin and attempted TFTP recovery
The TFTP transfer completed successfully (log attached – 20MB transferred in 9 seconds)
After transfer, the router’s internet LED flashed slowly for over 20 minutes
After power cycling, only the power LED is on
The router responds to ARP and has IP address 192.168.1.112
However:
Cannot access web interface at 192.168.1.112
Cannot connect via SSH or Telnet (connection timed out)
Internet LED does not light up normally
My question:
Is my router recoverable?
Do you have a special recovery tool or different firmware file for units with 128MB flash (if mine is one of those)?
Should I try a different recovery method?
tftplog : Connection received from 192.168.1.112 on port 2096 [13/03 05:40:51.666]
Read request for file . Mode octet [13/03 05:40:51.666]
File : error 2 in system call CreateFile The system cannot find the file specified. [13/03 05:40:51.667]
Connection received from 192.168.1.112 on port 2096 [13/03 05:41:25.544]
Read request for file . Mode octet [13/03 05:41:25.545]
File : error 2 in system call CreateFile The system cannot find the file specified. [13/03 05:41:25.545]
Connection received from 192.168.1.112 on port 2096 [13/03 05:42:08.362]
Read request for file . Mode octet [13/03 05:42:08.363]
OACK: <timeout=5,blksize=1468,> [13/03 05:42:08.363]
Using local port 51282 [13/03 05:42:08.363]
: sent 13664 blks, 20057628 bytes in 9 s. 1 blk resent [13/03 05:42:17.384]
Connection received from 192.168.1.112 on port 2096 [13/03 06:24:21.776]
Read request for file . Mode octet [13/03 06:24:21.776]
OACK: <timeout=5,blksize=1468,> [13/03 06:24:21.790]
Using local port 59907 [13/03 06:24:21.790]
: sent 13485 blks, 19795484 bytes in 9 s. 1 blk resent [13/03 06:24:30.652]
Connection received from 192.168.1.112 on port 2096 [13/03 06:25:19.368]
Read request for file . Mode octet [13/03 06:25:19.368]
OACK: <timeout=5,blksize=1468,> [13/03 06:25:19.368]
Using local port 56482 [13/03 06:25:19.368]
: sent 13485 blks, 19795484 bytes in 9 s. 1 blk resent [13/03 06:25:28.340]
Thank you for your support.
“Dear Cudy Support Team,
Doesn’t work
File is invalid. Please retry.
Uploaded File: cudy_wr3000e-v1-sysupgrade.bin
Size: 12.63 MB (13241931 B)
MD5: 77e6d84f93081732d4c130521078991a
@Dear Ahmed Elbiomy,
Our technical support has sent you the firmware via email. Please check.
“Dear Cudy Support Team,
I am writing to request the correct intermediate firmware file needed to install OpenWrt on my router.
My router details are:
· Model: Cudy WR3000E
· Hardware Version: v1.0
· Current Firmware Version: 2.2.6-20240902-033948
I have tried several intermediate files, but they were rejected. Could you please provide me with the correct intermediate firmware file compatible with my current firmware version?
Thank you for your assistance."
@Dear Grzegorz,
Our technical support has sent you the intermediate firmware via email. Please check.
In addition, your AP3000 supports VLAN mapping SSID function. You can set it on the web page of the AP3000 when creating the SSID. Please have a try.
""@Dear grzegorz,
What is the model of your Cudy AP?
my device:
Firmware Version 2.4.7-20260115-152710
Historic Version 2.4.7-20260115-152710
Model AP3000
Hardware AP3000 V1.0
“help mi !!
File is invalid. Please retry.
Uploaded File: openwrt-25.12.0-mediatek-filogic-cudy_ap3000wall-v1-squashfs-sysupgrade.bin
Size: 9.00 MB (9441562 B)
MD5: 72827a30761e73dee7020e58c7d7c477"
""
@Dear Ahmed Elbiomy,
Our technical support has sent you the firmware via email. Please check.
“Dear Cudy Support Team,
I am writing to request the correct intermediate firmware file needed to install OpenWrt on my router.
My router details are:
· Model: Cudy WR3000E
· Hardware Version: v1.0
· Current Firmware Version: 2.2.6-20240902-033948
I have tried several intermediate files, but they were rejected. Could you please provide me with the correct intermediate firmware file compatible with my current firmware version?
Thank you for your assistance."
Nie sety nie da się wgrać do mojego urządzenia AP3000 Wall 1.0.zip oto błąd
File is not compatible with the device model(s).
Uploaded File: cudy_ap3000wall-v1-sysupgrade_20251119.bin
Size: 14.25 MB (14945878 B)
MD5: 376d404fd1535cc51168e365e2374427
szczerze bardzo żałuje swojego zakupu mogłem kupić tplinka bo potrzebuje funkcji vlan gdzie tego w podstawie nie ma