警告
本網頁列出了支援OpenWrt系統的設備的軟體，在下載和安裝軟體之前，請注意OpenWrt Project是一個針對嵌入式設備的Linux作業系統。 OpenWrt 並沒有嘗試建立單一靜態韌體，而是提供了一個具有套件管理功能的完全可寫入檔案系統。這使您無需選擇供應商提供的應用程式和配置，並允許您透過使用軟體包來自訂設備以適應任何應用程式。對於開發人員來說，OpenWrt 是建立應用程式的框架，而無需圍繞它建立完整的韌體；對使用者來說，這意味著完全客製化的能力，以前所未有的方式使用裝置。
描述
- 此檔案僅當您的路由器在 Cudy Web UI 下運作時才能使用。
- 如果路由器已經在OpenWRT UI下工作，用戶應先將其恢復到Cudy官方韌體。然後用這個韌體升級路由器。
- 如何將路由器恢復至Cudy官方韌體？請閱讀下載文件中的自述文件。
保固：
Cudy特此聲明
- 我們 Cudy 對非深圳市 Cudy 科技有限公司發布的任何軟體不承擔任何保證。
- 對於安裝了非深圳市酷迪科技有限公司發布的任何軟體的產品，我們不承擔任何保證。
- 如果您需要使用openwrt軟體，建議您從Cudy官網下載。
下載 OpenWrt 韌體以刪除簽名檢查：驅動程式
OpenWrt 韌體查找器（不是由Cudy 發布）：OpenWrt 韌體選擇器
1319 則留言
Версия прошивки
2.4.19-20250828-192837
Аппаратная версия
WR3000 V1.0 SN:WR3000254901313 EAEU1.0
@Dear Паве,
Please check the model and Firmware page and send it to me again. I think you offer the wrong modle. Or you can send me the full SN number and send it to us for checking.
“Dear Cudy Support,
I am trying to install OpenWrt on my WR3000E V1.0 router but encountering an issue.
Device information:
- Model: WR3000E V1.0
- Serial Number: 2549XXXXX (new revision with NAND flash F50L1G41LC, SN ≥ 2543)
- Current firmware: 2.4.19-20250828-192837
Problem:
I downloaded the file “cudy_wr3000e-v1-sysupgrade_20251119.bin” (MD5: 249c150e7676facc9f33d79e634ec4a3) but the router rejects it with “Invalid file” error.
I understand that routers with SN ≥ 2543 require a special intermediary firmware compatible with the new flash chip (post-November 2025). The file dated 2025-11-19 appears to be for older revisions only.
Could you please provide the correct intermediary firmware for WR3000E V1.0 with new flash (SN 2549)?
Thank you for your assistance.
Best regards, Pavel"
Dear Cudy Support,
I am trying to install OpenWrt on my WR3000E V1.0 router but encountering an issue.
Device information:
- Model: WR3000E V1.0
- Serial Number: 2549XXXXX (new revision with NAND flash F50L1G41LC, SN ≥ 2543)
- Current firmware: 2.4.19-20250828-192837
Problem:
I downloaded the file “cudy_wr3000e-v1-sysupgrade_20251119.bin” (MD5: 249c150e7676facc9f33d79e634ec4a3) but the router rejects it with “Invalid file” error.
I understand that routers with SN ≥ 2543 require a special intermediary firmware compatible with the new flash chip (post-November 2025). The file dated 2025-11-19 appears to be for older revisions only.
Could you please provide the correct intermediary firmware for WR3000E V1.0 with new flash (SN 2549)?
Thank you for your assistance.
Best regards, Pavel
@Dear ahmed,
You router is WR3000, not WR3000E. I have sent you the correct firmware.
““Dear Cudy Support Team,
Doesn’t work
File is invalid. Please retry.
Uploaded File: cudy_wr3000e-v1-sysupgrade.bin
Size: 12.63 MB (13241931 B)
MD5: 77e6d84f93081732d4c130521078991a
@Dear Ahmed Elbiomy,
Our technical support has sent you the firmware via email. Please check.
“Dear Cudy Support Team,
I am writing to request the correct intermediate firmware file needed to install OpenWrt on my router.
My router details are:
· Model: Cudy WR3000E
· Hardware Version: v1.0
· Current Firmware Version: 2.2.6-20240902-033948
I have tried several intermediate files, but they were rejected. Could you please provide me with the correct intermediate firmware file compatible with my current firmware version?
Thank you for your assistance.""
Dear CUDY support! Earlier, with your help, I updated my AP3000 v1 to openwrt. Now I need to revert to the factory software. The LUCI web interface complains about an invalid file, and holding down the reset button and supplying power doesn’t work either. Can you help me figure out what to do?