Cudy Whole Home Mesh 系統旨在消除死區並在整個家庭中提供不間斷的 Wi-Fi。本文將引導您逐步建立一個Mesh Wi-Fi 系統。
準備工作：
1.確保您至少擁有 2 個 Cudy 產品。 Cudy所有產品均支援Mesh技術：首頁Mesh-Cudy官網
3.韌體是最新的：下載中心
4.配置時將它們放在同一個房間。將所有 Cudy 產品重設為出廠預設值。 （開機狀態下，用大頭針按住RESET按鈕6秒，然後放開。）
6.設定主路由器並使其連接到網際網路。
第 1 步：開啟網頁瀏覽器並造訪 http://cudy.net 或 http://192.168.10.1。
詳情請參考如何登入Cudy Router的Web介面？
第2步：在系統狀態頁面，點選"+"按鈕。
步驟 3：按 M1800 上的 WPS 按鈕，然後按下 WR2100 上的 WPS 按鈕。
主網格單元：白色閃爍
附加網格單元：白色和紅色交替閃爍
第4步：它將轉到"正在掃描"，然後"正在連接"。
第 5 步：等待附加路由器的系統 LED 變成藍色常亮，然後重新定位 WR2100。
第 6 步：成功並享受網狀網路。
註：
1. 4/5G 路由器只能設定為主網單元。例如：
2.您將無法登入附加網狀路由器的 Web 介面。如果您想要變更設置，請點選"系統狀態"->"網格"。
83 則留言
@Dear John,
1. Please check if the Mesh system is installed. You can login to the web page of the main mesh router, check the “Mesh” status card.
2. If yes, please check the status page of the satellite mesh router. Check if the backhaul is Wired?
3. If the backhaul is wired, please try to change the cable between the two router. Do you connect them directly or there is a switch between them?
4. What is the firmware version of the two routers? Please update to the latest and check again.
“I have two WR11000s which I’m trying to use as a mesh. The main router is connected to 1 Gbps fibre WAN. The secondary router is connected to the main router by wired ethernet (cat 6 cable).
When I plug my laptop into the secondary router with ethernet, I get a great connection (~800+ Mbps, according to speedtest.net). When I connect to the secondary router by wifi, the connection is hopeless — even sitting my laptop right next to the router, I get speeds of just a couple of Mbps, and lots of drop outs. This happens on all bands (2/5/6 GHz).
When I am connected to the main router by wifi, it works fine.
Any suggestions as to what might be going wrong?
Thanks!"
I have two WR11000s which I’m trying to use as a mesh. The main router is connected to 1 Gbps fibre WAN. The secondary router is connected to the main router by wired ethernet (cat 6 cable).
When I plug my laptop into the secondary router with ethernet, I get a great connection (~800+ Mbps, according to speedtest.net). When I connect to the secondary router by wifi, the connection is hopeless — even sitting my laptop right next to the router, I get speeds of just a couple of Mbps, and lots of drop outs. This happens on all bands (2/5/6 GHz).
When I am connected to the main router by wifi, it works fine.
Any suggestions as to what might be going wrong?
Thanks!
@Dear Kamil,
I think the camera is connected to the 2.4GHz WiFi of the router. You can try to change the mode of 2.4GHz to 802.11b+g+n mode. Then check if the camera is able to connect to it?
“I built a mesh network using four WR3600E routers, and the internet works great. However, this network was meant for cctv monitoring, and that’s where the problem appeared: when the routers are in mesh mode, the cameras won’t log into the network, no matter which WPA level we choose. Only after disabling encryption and the password do the cameras connect to Wi-Fi. The cameras are XMeye. Is there any solution? When connected to lan port everything works. I’ll add that when the router is not in mesh mode, the same camera connects to it normally with wifi. Regards.”
I built a mesh network using four WR3600E routers, and the internet works great. However, this network was meant for cctv monitoring, and that’s where the problem appeared: when the routers are in mesh mode, the cameras won’t log into the network, no matter which WPA level we choose. Only after disabling encryption and the password do the cameras connect to Wi-Fi. The cameras are XMeye. Is there any solution? When connected to lan port everything works. I’ll add that when the router is not in mesh mode, the same camera connects to it normally with wifi. Regards.
@Dear Paweł,
Yes, you can. You can choose on of the M3000 to be the main mesh device. Then set it to working on the Mesh Access Point mode. Connect it to the network. Then reset all other Cudy devices to factory default. For the second M3000, please connect to the WAN port to the network. For the APs, please connect to the network directly. The Mesh system will be install automatically.
“Hi,
I have no cudy router as my main router, I’m going to disable wifi on that router and cerate mesh system viavwired backhaul. can I connect via eth 2 cudy m3000 and 2 ap3000 and cerate wired mesh between them with having fast roaming without creating subnet.”