Cudy Whole Home Mesh 系統旨在消除死區並在整個家庭中提供不間斷的 Wi-Fi。本文將引導您逐步建立一個Mesh Wi-Fi 系統。
準備工作：
1.確保您至少擁有 2 個 Cudy 產品。 Cudy所有產品均支援Mesh技術：首頁Mesh-Cudy官網
3.韌體是最新的：下載中心
4.配置時將它們放在同一個房間。將所有 Cudy 產品重設為出廠預設值。 （開機狀態下，用大頭針按住RESET按鈕6秒，然後放開。）
6.設定主路由器並使其連接到網際網路。
第 1 步：開啟網頁瀏覽器並造訪 http://cudy.net 或 http://192.168.10.1。
詳情請參考如何登入Cudy Router的Web介面？
第2步：在系統狀態頁面，點選"+"按鈕。
步驟 3：按 M1800 上的 WPS 按鈕，然後按下 WR2100 上的 WPS 按鈕。
主網格單元：白色閃爍
附加網格單元：白色和紅色交替閃爍
第4步：它將轉到"正在掃描"，然後"正在連接"。
第 5 步：等待附加路由器的系統 LED 變成藍色常亮，然後重新定位 WR2100。
第 6 步：成功並享受網狀網路。
註：
1. 4/5G 路由器只能設定為主網單元。例如：
2.您將無法登入附加網狀路由器的 Web 介面。如果您想要變更設置，請點選"系統狀態"->"網格"。
83 則留言
@Dear Oli,
Cudy AP1300 can only install mesh system with Cudy product. If the speed is slow, may be there is some limit on the main router. You can try to set it to the Wireless Router mode and check.
“Recently installed an AP1300 in AP mode. Served via CAT 7 ethernet cable attached to the main internet router of the Internet Provider (diffrent brand). DIdn’t realize, that mesh is default while AP mode setup of the cudy. May mesh disturb, i.e. slow down connection of attached devices?”
Recently installed an AP1300 in AP mode. Served via CAT 7 ethernet cable attached to the main internet router of the Internet Provider (diffrent brand). DIdn’t realize, that mesh is default while AP mode setup of the cudy. May mesh disturb, i.e. slow down connection of attached devices?
@Dear Gabriel,
Basically, this is a hardware issue. May be caused by the cable or the router. We can have a compare test. You can choose one of the other two routers, Reset it and set it to be the main mesh router and connect to the same cable to check if it work on 1 Gbps or 100Mbps to judge the root cause.
“Dear Cudy Support,
I recently purchased a Cudy AX3000 Gigabit WiFi 6 Mesh Router along with two additional AX3000 mesh units, all of which support gigabit Ethernet ports.
My internet plan provides 200Mbps, and I am using undamaged Cat 6 Ethernet cables. The main router is connected to one of the mesh nodes via Ethernet. Up until yesterday, everything was working perfectly—I was getting full gigabit speeds through the LAN ports.
However, after rebooting the entire system today, the main router’s Ethernet ports are now only delivering 100Mbps. I’ve confirmed that the cables are properly seated and not damaged, and the same setup was previously delivering full gigabit speeds without issue.
Could you assist in identifying what might have caused this and how to resolve it?
Thank you"
Dear Cudy Support,
I recently purchased a Cudy AX3000 Gigabit WiFi 6 Mesh Router along with two additional AX3000 mesh units, all of which support gigabit Ethernet ports.
My internet plan provides 200Mbps, and I am using undamaged Cat 6 Ethernet cables. The main router is connected to one of the mesh nodes via Ethernet. Up until yesterday, everything was working perfectly—I was getting full gigabit speeds through the LAN ports.
However, after rebooting the entire system today, the main router’s Ethernet ports are now only delivering 100Mbps. I’ve confirmed that the cables are properly seated and not damaged, and the same setup was previously delivering full gigabit speeds without issue.
Could you assist in identifying what might have caused this and how to resolve it?
Thank you
@Dear Walter,
Yes, you can. The Cudy APs, such as the AP3000 and AP1300 can work as the main mesh device to manage other APs. You can set up one of the AP3000 and connect it to the network. Then connect other AP to the network. The mesh system will be installed automatically.
“Can I set up a mesh network using only Cudy AP’s? I have a different brand router so I want to build a mesh network with just the AP’s”