Avvertenze
Questa pagina web elenca il software dei dispositivi che supportano il sistema OpenWrt. Prima di scaricare e installare il software, tieni presente che OpenWrt Project è un sistema operativo Linux destinato ai dispositivi incorporati. Invece di provare a creare un singolo firmware statico, OpenWrt fornisce un filesystem completamente scrivibile con gestione dei pacchetti. Ciò ti libera dalla selezione e configurazione dell'applicazione fornita dal fornitore e ti consente di personalizzare il dispositivo attraverso l'uso di pacchetti adatti a qualsiasi applicazione. Per gli sviluppatori, OpenWrt è il framework per creare un'applicazione senza dover costruire attorno ad essa un firmware completo; per gli utenti questo significa la possibilità di personalizzazione completa, di utilizzare il dispositivo in modi mai immaginati.
Descrizione
- Questo file può essere utilizzato solo quando il router funziona con l'interfaccia utente web di Cudy.
- Se il router funziona già con l'interfaccia utente OpenWRT, l'utente deve prima ripristinarlo sul firmware ufficiale Cudy. E poi aggiorna il router con questo firmware.
- Come ripristinare il router sul firmware ufficiale Cudy? Si prega di leggere il file Leggimi nel file scaricato.
Garanzia:
Cudy dichiara
- Noi, Cudy, non ci assumiamo alcuna garanzia per alcun software che non sia rilasciato da Shenzhen Cudy Technology Co., Ltd.
- Non assumiamo alcuna garanzia per i prodotti che hanno installato software non rilasciato da Shenzhen Cudy Technology Co., Ltd.
- Se hai bisogno di utilizzare il software openwrt, ti suggeriamo di scaricarlo dal sito Web ufficiale di Cudy.
Scarica il firmware OpenWrt per rimuovere il controllo della firma: Drive
Ricerca firmware OpenWrt (non rilasciato da Cudy): Selettore firmware OpenWrt
1530 commenti
Hello.
I have a Cudy WR3000 V1.0 router.
Serial number starts with: 2532
Current stock firmware: 2.4.19-20250828-192837
I would like to install official OpenWrt.
Please send me the latest Cudy-signed OpenWrt intermediate firmware compatible with my WR3000 V1.0 and this hardware/flash revision.
Thank you.
Hello,
I have a Cudy WR3000 V1.0 EU router.
Serial number starts with: 2539
Current stock firmware: 2.4.19-20250828-192837
I would like to install official OpenWrt.
Please send me the latest Cudy-signed OpenWrt intermediate firmware compatible with my WR3000 V1.0 and this hardware revision.
Thank you.
Greetings,
I would like to request for the signed openwrt firmware for M3000 with a Motorcomm YT8821 (Variant 2) please.
Thanks
@Dear Mike,
The firmware file in Google Drive is correct. This is for both hardware version. Please unzip the file before update.
Note: If you have installed Mesh system with the router. You can’t update the firmware. Please power off the other Mesh device. Then reset this router to factory default. You can update this firmware before mesh system installed.
“Hi,
I would also like to request the M3000 V.2 with the Motorcomm YT8821 chip, if that’s possible.
Thank you.”
@Dear Горбунов Михаил,
I think there is some hardware faulty in the router. You can try to contact the seller to request a replacement and try again.
“Hello. I specifically need to install OpenWrt on a Cudy M3000 V2.0. The current issue is not simply with the stock firmware, but with the OpenWrt installation process and the intermediate firmware file.
The situation is as follows:
Router: Cudy M3000 V2.0
I used the intermediate firmware file intended for transitioning from the stock Cudy firmware to OpenWrt.
After flashing that intermediate file, the router does not boot into OpenWrt correctly.
The Ethernet connection periodically goes down and comes back up.
The router appears to enter a reboot/boot loop, with the LED changing states.
There is no stable access to OpenWrt at 192.168.1.1.
Sometimes 192.168.10.1 becomes available again.
So my goal is not just to restore the stock firmware. I need to successfully complete the installation of OpenWrt.
Could you please clarify:
After flashing your intermediate file, should the M3000 V2.0 boot directly into OpenWrt?
If yes, why might my router be entering a boot loop instead of booting OpenWrt?
Is another firmware file required after the intermediate file?
If so, which exact OpenWrt image should be used for Cudy M3000 V2.0?
Should it be a factory.bin, sysupgrade.bin, or a special recovery/install image?
If the next step must be performed via TFTP, please provide the exact procedure:
required filename;
PC IP address;
router IP address;
which LAN port to use;
RESET/power-on sequence;
which firmware image should be transferred.
Could this problem be caused by the intermediate firmware itself or by a specific hardware revision of the M3000 V2.0?
What I need is a working step-by-step procedure for installing OpenWrt on the M3000 V2.0 from its current state, because at the moment the intermediate firmware does not result in a successful OpenWrt boot.
If necessary, I can provide a video of the boot loop, ipconfig/ping output, and the current stock firmware version."