Il sistema Cudy Whole Home Mesh è progettato per eliminare le zone morte e fornire Wi-Fi ininterrotto in tutta la casa. Questo articolo ti guiderà nella creazione di un sistema mesh passo dopo passo.
Preparazione:
1. Assicurati di possedere almeno 2 prodotti Cudy.
2. Tutti i prodotti Cudy supportano la tecnologia mesh: Home Sito ufficiale Mesh-Cudy
3. Il firmware è aggiornato: Centro download
4. Portali nella stessa stanza durante la configurazione.
5. Ripristina tutti i tuoi prodotti Cudy alle impostazioni predefinite di fabbrica. (Con l'alimentazione accesa, tieni premuto il pulsante RESET con uno spillo per 6 secondi, quindi rilascialo.)
6. Configura il tuo router principale e collegalo a Internet.
Qui prendiamo M1800 e WR2100 come esempi:
Passaggio 1: apri un browser web e vai su http://cudy.net o http://192.168.10.1.
Per i dettagli, fare riferimento a Come accedere all'interfaccia web di Cudy Router?
Passaggio 2: nella pagina Stato del sistema, fare clic su Pulsante "+".
Passaggio 3: premi il pulsante WPS sull'M1800, quindi premi il pulsante WPS sul WR2100.
Unità mesh principale: Flash bianco
Unità mesh aggiuntiva: Flash bianco e rosso alternativamente
Passaggio 4: Andrà a " Scansione", quindi " Connessione".
Passaggio 5: attendi finché il LED di sistema del router aggiuntivo non diventa blu fisso, quindi riposiziona il WR2100.
Passaggio 6: ottieni successo e goditi la rete mesh.
Nota:
1. Il router 4/5G può essere configurato solo come unità mesh principale. Ad esempio:
2. Non potrai accedere all'interfaccia web del router mesh aggiuntivo. Se desideri modificare le impostazioni, fai clic su "Stato del sistema"->"Mesh".
79 commenti
Tengo un router del proveedor que me genera una red wifi, tengo tres Cudy M3000 wifi y quiero por medio de cable ethernet repitan la red wifi del router del proveedor con el mismo nombre y la misma contraseña
@Dear John,
1. Please check if the Mesh system is installed. You can login to the web page of the main mesh router, check the “Mesh” status card.
2. If yes, please check the status page of the satellite mesh router. Check if the backhaul is Wired?
3. If the backhaul is wired, please try to change the cable between the two router. Do you connect them directly or there is a switch between them?
4. What is the firmware version of the two routers? Please update to the latest and check again.
“I have two WR11000s which I’m trying to use as a mesh. The main router is connected to 1 Gbps fibre WAN. The secondary router is connected to the main router by wired ethernet (cat 6 cable).
When I plug my laptop into the secondary router with ethernet, I get a great connection (~800+ Mbps, according to speedtest.net). When I connect to the secondary router by wifi, the connection is hopeless — even sitting my laptop right next to the router, I get speeds of just a couple of Mbps, and lots of drop outs. This happens on all bands (2/5/6 GHz).
When I am connected to the main router by wifi, it works fine.
Any suggestions as to what might be going wrong?
Thanks!"
I have two WR11000s which I’m trying to use as a mesh. The main router is connected to 1 Gbps fibre WAN. The secondary router is connected to the main router by wired ethernet (cat 6 cable).
When I plug my laptop into the secondary router with ethernet, I get a great connection (~800+ Mbps, according to speedtest.net). When I connect to the secondary router by wifi, the connection is hopeless — even sitting my laptop right next to the router, I get speeds of just a couple of Mbps, and lots of drop outs. This happens on all bands (2/5/6 GHz).
When I am connected to the main router by wifi, it works fine.
Any suggestions as to what might be going wrong?
Thanks!
@Dear Kamil,
I think the camera is connected to the 2.4GHz WiFi of the router. You can try to change the mode of 2.4GHz to 802.11b+g+n mode. Then check if the camera is able to connect to it?
“I built a mesh network using four WR3600E routers, and the internet works great. However, this network was meant for cctv monitoring, and that’s where the problem appeared: when the routers are in mesh mode, the cameras won’t log into the network, no matter which WPA level we choose. Only after disabling encryption and the password do the cameras connect to Wi-Fi. The cameras are XMeye. Is there any solution? When connected to lan port everything works. I’ll add that when the router is not in mesh mode, the same camera connects to it normally with wifi. Regards.”
I built a mesh network using four WR3600E routers, and the internet works great. However, this network was meant for cctv monitoring, and that’s where the problem appeared: when the routers are in mesh mode, the cameras won’t log into the network, no matter which WPA level we choose. Only after disabling encryption and the password do the cameras connect to Wi-Fi. The cameras are XMeye. Is there any solution? When connected to lan port everything works. I’ll add that when the router is not in mesh mode, the same camera connects to it normally with wifi. Regards.