警告
本網頁列出了支援OpenWrt系統的設備的軟體，在下載和安裝軟體之前，請注意OpenWrt Project是一個針對嵌入式設備的Linux作業系統。 OpenWrt 並沒有嘗試建立單一靜態韌體，而是提供了一個具有套件管理功能的完全可寫入檔案系統。這使您無需選擇供應商提供的應用程式和配置，並允許您透過使用軟體包來自訂設備以適應任何應用程式。對於開發人員來說，OpenWrt 是建立應用程式的框架，而無需圍繞它建立完整的韌體；對使用者來說，這意味著完全客製化的能力，以前所未有的方式使用裝置。
描述
- 此檔案僅當您的路由器在 Cudy Web UI 下運作時才能使用。
- 如果路由器已經在OpenWRT UI下工作，用戶應先將其恢復到Cudy官方韌體。然後用這個韌體升級路由器。
- 如何將路由器恢復至Cudy官方韌體？請閱讀下載文件中的自述文件。
保固：
Cudy特此聲明
- 我們 Cudy 對非深圳市 Cudy 科技有限公司發布的任何軟體不承擔任何保證。
- 對於安裝了非深圳市酷迪科技有限公司發布的任何軟體的產品，我們不承擔任何保證。
- 如果您需要使用openwrt軟體，建議您從Cudy官網下載。
下載 OpenWrt 韌體以刪除簽名檢查：驅動程式
OpenWrt 韌體查找器（不是由Cudy 發布）：OpenWrt 韌體選擇器
1530 則留言
Hello.
I have a Cudy WR3000 V1.0 router.
Serial number starts with: 2532
Current stock firmware: 2.4.19-20250828-192837
I would like to install official OpenWrt.
Please send me the latest Cudy-signed OpenWrt intermediate firmware compatible with my WR3000 V1.0 and this hardware/flash revision.
Thank you.
Hello,
I have a Cudy WR3000 V1.0 EU router.
Serial number starts with: 2539
Current stock firmware: 2.4.19-20250828-192837
I would like to install official OpenWrt.
Please send me the latest Cudy-signed OpenWrt intermediate firmware compatible with my WR3000 V1.0 and this hardware revision.
Thank you.
Greetings,
I would like to request for the signed openwrt firmware for M3000 with a Motorcomm YT8821 (Variant 2) please.
Thanks
@Dear Mike,
The firmware file in Google Drive is correct. This is for both hardware version. Please unzip the file before update.
Note: If you have installed Mesh system with the router. You can’t update the firmware. Please power off the other Mesh device. Then reset this router to factory default. You can update this firmware before mesh system installed.
“Hi,
I would also like to request the M3000 V.2 with the Motorcomm YT8821 chip, if that’s possible.
Thank you.”
@Dear Горбунов Михаил,
I think there is some hardware faulty in the router. You can try to contact the seller to request a replacement and try again.
“Hello. I specifically need to install OpenWrt on a Cudy M3000 V2.0. The current issue is not simply with the stock firmware, but with the OpenWrt installation process and the intermediate firmware file.
The situation is as follows:
Router: Cudy M3000 V2.0
I used the intermediate firmware file intended for transitioning from the stock Cudy firmware to OpenWrt.
After flashing that intermediate file, the router does not boot into OpenWrt correctly.
The Ethernet connection periodically goes down and comes back up.
The router appears to enter a reboot/boot loop, with the LED changing states.
There is no stable access to OpenWrt at 192.168.1.1.
Sometimes 192.168.10.1 becomes available again.
So my goal is not just to restore the stock firmware. I need to successfully complete the installation of OpenWrt.
Could you please clarify:
After flashing your intermediate file, should the M3000 V2.0 boot directly into OpenWrt?
If yes, why might my router be entering a boot loop instead of booting OpenWrt?
Is another firmware file required after the intermediate file?
If so, which exact OpenWrt image should be used for Cudy M3000 V2.0?
Should it be a factory.bin, sysupgrade.bin, or a special recovery/install image?
If the next step must be performed via TFTP, please provide the exact procedure:
required filename;
PC IP address;
router IP address;
which LAN port to use;
RESET/power-on sequence;
which firmware image should be transferred.
Could this problem be caused by the intermediate firmware itself or by a specific hardware revision of the M3000 V2.0?
What I need is a working step-by-step procedure for installing OpenWrt on the M3000 V2.0 from its current state, because at the moment the intermediate firmware does not result in a successful OpenWrt boot.
If necessary, I can provide a video of the boot loop, ipconfig/ping output, and the current stock firmware version."