1.從 這裡。
2.從 官方網站並將其重新命名為"recovery.bin"。
3.關閉路由器電源。拔掉電源供應器或按電源按鈕。
4.使用乙太網路線將電腦連接到路由器的 LAN 連接埠。
5.手動將電腦的 IP 位址配置為"192.168.1.88"。 6.執行"tftp32.exe"。
7.在命令列中執行"netsh advfirewall set allprofiles state off"來停用Windows防火牆，否則tftp將被阻止。
8.按下"重設"按鈕/孔並按住。在路由器開機和 tftp 開始下載韌體之前，請勿放開"重設"按鈕/孔。 9.開啟路由器電源。 10。當指示燈全部快速閃爍時，或 tftp 開始下載韌體時，您可以放開"重設"按鈕/孔。
11.當燈慢閃時，升級完成。
12.請將您電腦的IP位址還原為動態IP。 13.完成。
223 則留言
Ссылки не работают, судя по комментариям компания больше не хочет что бы люди пользовались их ПО?
Я хочу восстановить официальную прошивку на WR3000S, как мне это теперь сделать?
@Dear Alan,
Our technical support has contacted you via email. Please check.
“Thank you for your response. However, it did not resolve my issues.
Currently, my TR3000-256MB router when in a normal boot state. After plugging in the power cable, the red and white LEDs keep flashing, and my computer’s LAN connection is continuously going on and off. I attempted to set a static IP address of 192.168.1.2 on my computer, but I cannot ping or connect to the router’s webpage at 192.168.1.1.
When I try to use TFTP, the router does not respond to my computer’s IP (192.168.1.88), but it does respond to 192.168.1.2. After sending the recovery.bin file (downloaded from the mainland webpage: TR3000_256MB_Flash-R103-2.3.9-20250208-171917-sysupgrade.bin) to the router, it does not reboot on its own, and the LEDs continue to flash red and white.
The loop is continuous. Am I flashing the correct file? Is there any other way to restore the factory firmware?"
Thank you for your response. However, it did not resolve my issues.
Currently, my TR3000-256MB router when in a normal boot state. After plugging in the power cable, the red and white LEDs keep flashing, and my computer’s LAN connection is continuously going on and off. I attempted to set a static IP address of 192.168.1.2 on my computer, but I cannot ping or connect to the router’s webpage at 192.168.1.1.
When I try to use TFTP, the router does not respond to my computer’s IP (192.168.1.88), but it does respond to 192.168.1.2. After sending the recovery.bin file (downloaded from the mainland webpage: TR3000_256MB_Flash-R103-2.3.9-20250208-171917-sysupgrade.bin) to the router, it does not reboot on its own, and the LEDs continue to flash red and white.
The loop is continuous. Am I flashing the correct file? Is there any other way to restore the factory firmware?
@Dear Alan,
The LAN IP address will be changed from 192.168.10.1 to 192.168.1.1 after firmware update. You need to set the IP address to DHCP to get the IP address from the router.
You need to connect your computer to the LAN port of the router. Then try to login to the web page of the router via the IP address 192.168.1.1.
“Hi, I want to flash my TR300-256Mb router to OpenWrt, but after using the “cudy_tr3000-256mb-v1-sysupgrade.bin” file, it doesn’t display any pages upon reboot. The red and white LEDs keep flashing. I attempted to use TFTP for recovery, but unfortunately, I can’t revert to the original firmware. The same LED signal persists.
So, What can I do?”
Hi, I want to flash my TR300-256Mb router to OpenWrt, but after using the “cudy_tr3000-256mb-v1-sysupgrade.bin” file, it doesn’t display any pages upon reboot. The red and white LEDs keep flashing. I attempted to use TFTP for recovery, but unfortunately, I can’t revert to the original firmware. The same LED signal persists.
So, What can I do?