1.從 這裡。
2.從 官方網站並將其重新命名為"recovery.bin"。
3.關閉路由器電源。拔掉電源供應器或按電源按鈕。
4.使用乙太網路線將電腦連接到路由器的 LAN 連接埠。
5.手動將電腦的 IP 位址配置為"192.168.1.88"。 6.執行"tftp32.exe"。
7.在命令列中執行"netsh advfirewall set allprofiles state off"來停用Windows防火牆，否則tftp將被阻止。
8.按下"重設"按鈕/孔並按住。在路由器開機和 tftp 開始下載韌體之前，請勿放開"重設"按鈕/孔。 9.開啟路由器電源。 10。當指示燈全部快速閃爍時，或 tftp 開始下載韌體時，您可以放開"重設"按鈕/孔。
11.當燈慢閃時，升級完成。
12.請將您電腦的IP位址還原為動態IP。 13.完成。
223 則留言
@Caro Marco,
il nostro supporto tecnico ti ha contattato via e-mail. Ti preghiamo di controllare.
“Buongiorno ho un modem cudy p5 5g da quando ho fatto aggiornamento a settembre2025 non si connette in 5g rimane solo 4g che posso fare?”
I have a cudy n700, it does not seem to reset or enter recovery mode, this is the second one with the same issue can you assist with resolving this urgently
@Dear Otis,
I think there is something wrong with the router. The router can’t be recovered.
“Hello , i have a CudyWR3000 and i wish to put it in recovery mode so that i can tftp my way into openwrt , the issue is , i can not put in recovery mode , i have tried holding the reset button while its unplugged and then plug it back in and keep holding for 12 seconds , at times even longer and no matter what i do , i do not get a rapidly blinking light indicating recovery mode , all i get is a steady power led and the internet led slowly blinking ( mind you when its in that mode which is not recovery no other light is on , just those two) . I thought that perhaps its recovery mode and i am missing something , i went on with the process the same way i would with it being in recovery , no matter how many times i tried or changes i made tcpdump indicated no request coming from the router .”
@Estimado Javier:
De acuerdo. Creo que está relacionado con el canal de trabajo. Algunos canales no admiten 160 MHz.
“He tenido que volver a las versión del Firmware original, ya que en Openwrt al configurar la Wifi 5G en ancho de banda 160 mhz, desparece y no se puede conectar. He hecho muchas pruebas y es cambiarlo a 80 mhz y si funciona. Este problema con el firm de Cudy no pasa. Se queda configurado en 160mhz y todo normal.”
Hello , i have a CudyWR3000 and i wish to put it in recovery mode so that i can tftp my way into openwrt , the issue is , i can not put in recovery mode , i have tried holding the reset button while its unplugged and then plug it back in and keep holding for 12 seconds , at times even longer and no matter what i do , i do not get a rapidly blinking light indicating recovery mode , all i get is a steady power led and the internet led slowly blinking ( mind you when its in that mode which is not recovery no other light is on , just those two) . I thought that perhaps its recovery mode and i am missing something , i went on with the process the same way i would with it being in recovery , no matter how many times i tried or changes i made tcpdump indicated no request coming from the router .