Akcesoria PoE
POE10

Max 250 m Distance

Connect Further. Deploy Flexibly.

Choose the high-speed mode to establish a PoE Gigabit connection that spans for another 100 m, or long-range mode to prolong the connection to 250 m by limiting the speed at 10 Mbps.

Max 250 m Distance

Connect Further. Deploy Flexibly.

Choose the high-speed mode to establish a PoE Gigabit connection that spans for another 100 m, or long-range mode to prolong the connection to 250 m by limiting the speed at 10 Mbps.

Built for Consistent Networking 24/7

Shields Against Static Discharge

Dry office environment may harm the client with static discharge, and POE10 is equipped with level 3 ESD protection, handling 6kV contact and 8kV air ESD.

Tri-Level Client Protections

Provide more reliable networking with short-circuit protection, overvoltage protection, and polarity protection.

High-Speed. Plug and Play.

Gigabit Speed

Provides super-fast bandwidth suitable for connecting multiple cameras, high-speed access points, speakers down the line. *Connecting mulitple clients requries additional network switch at its end.

Wall-Mount Ready

Installation is straightforward with no configuration required. Mounting screws are included in the box.

FAQ

  1. What is a PoE Extender?
    A PoE Extender allows you to extend both power and data over Ethernet beyond the standard 100 m (328 ft) limit. It receives PoE input from a PoE switch or injector and outputs power and data to the next device or another extender.
  2. Can I connect a PoE Extender directly to a non-PoE switch?
    No. A non-PoE switch does not provide power through Ethernet.
    You must use a PoE injector between the switch and the extender to supply power if you do not have a PoE switch.
  3. My PoE Extender is not working. What should I check first?
    Please verify the following:
  • The upstream device (switch or injector) supports PoE or PoE+ (802.3af/at).
  • Non-PoE switches cannot power the extender.
  • The Ethernet cable is Cat5e or higher, in good condition, and under 100 m per segment.
  • The total chain length (from the switch to the final device) does not exceed the maximum supported distance.
  • The powered device (PD), such as a camera or AP, does not exceed the extender’s PoE output capacity.
1 3

Przedłużacz PoE

Przedłużacz PoE, POE10 2.0

POE10 2.0

Extender PoE wydłużający zasięg PoE o 100m.

  • GbE In, GbE Out
  • 802.3at/af Max 30W Output 1
  • 802.3at/af Input
  • High-Speed/Long-Range Modes
  • High-Speed Extension up to 100 meters 2
  • Extend for 250 meters Transmission 3
  • Wall-Mount
Pokaż kompletne dane
Wersja modelu
Wersja modelu POE10 2.0
Protocols
Protocols 802.3 Protocols
  • 802.3i 10 Mbps over Twisted Pair
  • 802.3u 100 Mbps over Twisted Pair
  • 802.3ab 1 Gbps over Twisted Pair
  • 802.3x Flow Control
  • 802.3af PoE
  • 802.3at PoE
PoE
PoE Uplink Stream 1× GbE, 802.3at/af
Uplink PIN Assignment Mode A / Mode B
Downlink Stream 1× GbE, 802.3at/af
Downlink Pin Assignment Mode A
Transimission Distance
  • Cat. 5e or higher cable: 100 meters at Gigabit
  • Cat. 5e or higher cable: 250 meters at 10 Mbps
  • Note: Distance from extender to switch depends on switch capability. Distance from extender to device follows extender rating
Transimission Distance Note 250-meter transmission is only available under the Long-Range mode.
Interfaces
Interfaces Physical Buttons High-Speed/Long-Range DIP Switch
LED
  • PoE Status of Each PoE Port
  • Link/ACT of Each Ethernet Port
Power
Power Power Methods 802.3at/af PoE
Passive PoE Input 48V
Power Input ≥30W is recommended
Max Power Output 30W
Max Power Output Note The actual power output depends on input
Max Power Consumption (W) 2W
Reliability
Reliability Power Protection
  • Polarity Protection
  • Overvoltage Protection
  • Short-Circuit Protection
EMC IEC/EN 61000-4-2, Level 3 ESD: Contact: 6kV; Air: 8kV
IEC/EN 61000-4-5, Level 3 Surge: RJ45: CM 2kV
Environment Ambient Operating Temperature: 0~40 ℃ (32~104 ℉)
Storage Temperature: -40~70 ℃ (-40~158 ℉)
Operating Humidity: 10%~95% non-condensing
Storage Humidity: 5%~95% non-condensing
Certifications
Certifications FCC, CE
Mechanical
Mechanical Install in a Daisy Chain Up to 3 extenders in a chain
Installation
  • Desktop
  • Wall-mount
Dimension Main Part:
80.1×48.9×31.9 mm
3.15×1.93×1.26 inches
Each Bracket:
9 mm
0.35 inches
Casing Material Plastic
Product Weight 58.4 g (2.06 oz.)
Package Content
Package Content
  • POE10
  • Mounting Kit
  • Installation Guide
Ordering Information
Ordering Information Retail Package Dimension 106.5×53×40 mm
4.19×2.09×1.57 inches
Retail Package Weight 89.0 g (3.14 oz.)
Units per Carton 100
Carton Net Weight 8.9 kg (19.62 lbs)
Carton Gross Weight 9.5 kg (20.94 lbs)
Carton Dimension 45.2×22×29.4 cm
17.8×8.66×11.57 inches
  1. The actual available power equals the uplink power minus the loss on the line and device’s own power consumption (see the power consumption in the spec sheet). A PoE switch or PoE adapter that supports standard IEEE PoE standard at 54 V is recommended as the uplink power source.
  2. 100m extension is measured from the GbE out to the client devices. The section between uplink switch and GbE In is determined by the uplink switch.
  3. The speed will be limited at 10 Mbps under the Extend/Long-Range mode.