1. Download and unzip the file from here.
2. Download the latest firmware from the official website and rename it to 'recovery.bin'. Note: You must put it in the same file of Tftpd tools.
3. Power off your Router. Unplug the power adapter or press the POWER button.
4. Connect your computer the Router's LAN port with an Ethernet cable.
5. Configure your computer's IP address to be '192.168.1.88' manually.
6. Run 'tftp32.exe'.
7. Run 'netsh advfirewall set allprofiles state off' in the command line to disable Windows firewall, otherwise tftp will be blocked. Or you can disable the firewall on the Control Panel of your computer. As shown below.
8. Press the 'Reset' button/hole and hold it. Before the Router is powered on and before tftp start to download the firmware, don't release the 'Reset' button/hole.
9. Power on the Router.
10. When the Lights are all flashing fast, or when tftp start to download the firmware, you can release the 'Reset' button/hole.
11. When the light flashes slowly, the upgrade is complete.
12. Please recover your computer's IP address to be dynamic IP.
13. Done.
142 comments
@Уважаемый Павел,
Какая прошивка у вашего Cudy TR30 (TR3000)? Это последняя версия прошивки 2.4.7? Если нет, пожалуйста, сначала обновите прошивку. Затем проверьте еще раз.
“Здравствуйте! При подключении к Cudy TR30 (TR3000) LTE модема, нет соединения. В настройках Cudy USB соединение неактивно. Что можно сделать?”
@Dear Alan,
So, why do you think it is the 256MB version. The 256MB version is only available for sell in China. The words on the label are in Chinese language, please have a check.
“Regarding the previous issue (failure to recover TR3000-256MB), I was finally able to revive it from being bricked using TTL. My router itself has no any hardware faults. I discovered that the NAND chip’s memory size differs from what is indicated on the box or label. This mismatch led to flashing the wrong version, causing it to become bricked and continuously reboot.
The chip inside is an ESMT F50L1G41LB, which can be broken down as follows:
F – Manufacturer: ESMT 50 – Product Collection L – Low Voltage (DDR3L) 1G – Density: 1Gb (Single Capacity) 41 – Organizational Structure: x16 (16-bit wide) LB – Packages and Versions
The capacity of a single unit is calculated as follows:
1Gb ÷ 8 bits/byte = 128MB
I hope you all don’t have to deal with the same issue I experienced. I’ve reached out to sales@cudy.com but haven’t received a response yet."
Здравствуйте! При подключении к Cudy TR30 (TR3000) LTE модема, нет соединения. В настройках Cudy USB соединение неактивно. Что можно сделать?
Regarding the previous issue (failure to recover TR3000-256MB), I was finally able to revive it from being bricked using TTL. My router itself has no any hardware faults. I discovered that the NAND chip’s memory size differs from what is indicated on the box or label. This mismatch led to flashing the wrong version, causing it to become bricked and continuously reboot.
The chip inside is an ESMT F50L1G41LB, which can be broken down as follows:
F – Manufacturer: ESMT 50 – Product Collection L – Low Voltage (DDR3L) 1G – Density: 1Gb (Single Capacity) 41 – Organizational Structure: x16 (16-bit wide) LB – Packages and VersionsThe capacity of a single unit is calculated as follows:
1Gb ÷ 8 bits/byte = 128MB
I hope you all don’t have to deal with the same issue I experienced. I’ve reached out to sales@cudy.com but haven’t received a response yet.
@Уважаемый Павел,
Пожалуйста, следуйте этой инструкции шаг за шагом. Если это не поможет, попробуйте выполнить эту операцию на другом компьютере.
“Здравствуйте! После прошивки роутера Cudy TR30 (TR3000) на OpenWRT решил прошить на заводскую прошивку и видимо бэкап не прошился. Теперь роутер не загружается и не заходит в web панель управления. Как можно это исправить?”