OpenWrt 軟體下載

@Dear Bourn,

There is no OpenWrt firmware for AP1300 V1.0 currently. The OpenWrt firmware is not developed by Cudy but by the developers. We need the OpenWrt forum official support the router at first, then we can release a middle firmware for you, then you can use and upgrade to the OpenWrt firmware.
“Hello,

I own a Cudy AP1300 1.0 access point and would like to install OpenWrt.

https://www.cudy.com/products/ap1300-1-0

Could you please provide an OpenWrt firmware image without signature verification that can be installed via the stock web interface?"

Hi Cudy Support Team , I’ve tried what you suggested – flashing older official firmware, but no luck , my Cudy WR3000 v1 is still bootlooping. Is there any firmware or recovery steps that I might perform in order to recover my router so I be able to boot into GUI ?
One more note : after flashing your firmware from Google drive or OpenWRT firmware, I’m able to enter to OpenWRT failsafe mode and access router via LAN using SSH , but from there I wasn’t able to perform system restoration steps from OpenWRT guides( I just don’t know how to do it propertly) . Thanks is advice for your support.

“@Dear Michael,
You can try to recover the old firmware version. Such as the 2.0.0, 2.2.6. Please connect the LAN port when recovering the firmware.

“Hi Cudy Support Team , I have purchased cudy wr3000 v1 router at the end of y 2023 ,I’ve successpully installed openwrt on my router using intermideate Cudy firmware, that was about 2 years ago. Then year after at 2024 ,I decided to go back to Cudy’s official firmware using OpenWrt system update and latest official firware at that moment .But something went wrong ( as I understood, there was some internal flash incompatibility with newer firmwares and older routers caused by internal flash)
As for today 2026 , my WR3000 v1 router is bootlooping endlessly but I’m able to upload firmware using tftp64.
What I’ve tried:
– Uploading latest official firmware v WR3000-R31-2.4.19 via tftp64 (using WAN port and LAN1 port )
– Uploading itermideate firmware from google drive , using tftp64 via LAN1 port and WAN port ,
– Uploading latest openwrt firmware v24.10.5 using tftp64 via WAN and LAN1 port .
- Uploading openwrt kernel only firmware based on v24.10.5 via WAN and LAN1 port .
Only when uploade official Cudy firmware ,the device rebooted itself autoamtically afer 3-4 minutes. In all cases the device is bootloping after manual or automatic restart.
Do you have any suggestions ? Maybe some firwmare to restore the device ?”"

WR3000P2550 . Can’t change to intermdiate cudy_wr3000p-v1-sysupgrade_20251119.bin: “File is invalid. Please retry.”
is it possible to get openwrt for WR3000P with new serial number?

Hello,

I own a Cudy AP1300 1.0 access point and would like to install OpenWrt.

https://www.cudy.com/products/ap1300-1-0

Could you please provide an OpenWrt firmware image without signature verification that can be installed via the stock web interface?

@Dear Roman,
Please try to update the intermediate firmware again. Note: The IP address of the router will change to 192.168.1.1 after update. You must check if your computer gets the correct IP address from the router and login the web page with 192.168.1.1.

“Hello! I do have Cudy WR3000E v1.0 with S/N: WR3000E254702030 having problem installing Intermediate firmware to install OpenWrt after that. I’ve tried to install cudy_wr3000e-v1-sysupgrade_20251119.bin from https://drive.google.com/drive/folders/1BKVarlwlNxf7uJUtRhuMGUqeCa5KpMnj but the router won’t start after installing it. Only 1 LED of Power is working so i have to start the recovery process with Tftpd64.”