OpenWrt 軟體下載

警告

本網頁列出了支援OpenWrt系統的設備的軟體，在下載和安裝軟體之前，請注意OpenWrt Project是一個針對嵌入式設備的Linux作業系統。 OpenWrt 並沒有嘗試建立單一靜態韌體，而是提供了一個具有套件管理功能的完全可寫入檔案系統。這使您無需選擇供應商提供的應用程式和配置，並允許您透過使用軟體包來自訂設備以適應任何應用程式。對於開發人員來說，OpenWrt 是建立應用程式的框架，而無需圍繞它建立完整的韌體；對使用者來說，這意味著完全客製化的能力，以前所未有的方式使用裝置。

描述

  1. 此檔案僅當您的路由器在 Cudy Web UI 下運作時才能使用。
  2. 如果路由器已經在OpenWRT UI下工作，用戶應先將其恢復到Cudy官方韌體。然後用這個韌體升級路由器。
  3. 如何將路由器恢復至Cudy官方韌體？請閱讀下載文件中的自述文件。

保固：

Cudy特此聲明

  1. 我們 Cudy 對非深圳市 Cudy 科技有限公司發布的任何軟體不承擔任何保證。
  2. 對於安裝了非深圳市酷迪科技有限公司發布的任何軟體的產品，我們不承擔任何保證。
  3. 如果您需要使用openwrt軟體，建議您從Cudy官網下載。

下載 OpenWrt 韌體以刪除簽名檢查：驅動程式

OpenWrt 韌體查找器（不是由Cudy 發布）：OpenWrt 韌體選擇器 

返回網誌

1319 則留言

нет прошивки на WBR3000UAX. где её можно скачать ?

Андрей

Hi Jaddie, even going back to 2.0.0 did not work here. Still getting the file is invalid message. A 2nd hand Aruba is on its way to me now, if it works then there will be some Cudy kit going on eBay!

Jon

Jon Fear

I have two Cudy M1800 with firmware version 2.1.3-20240509-102323. I tried to use the file in M1800+V2.zip. However, it says “Not applicable！Please upload the firmware applicable to the following models.” if I try to update firmware from Advance Settings → Firmware. If I try to update the firmware of a specific model, it says “File is invalid. Please retry.”. I have tried downgrading the firmware version of the M1800 devices to 1.16.14-20231117-190903. It gives the same error. What should I do?

Muhammed Tasnim Bin Anwar

@Support & @Jon
That seems to be working, Jon if you follow the 2nd link they gave, there is a 2nd place to update the firmware which works, the normal one errored for me too, but doing it where the 2nd guide shows it is now rolling back to v2.0.0 at which point openwrt should install

Jaddie

Following the openwrt saga. I have several M3000 v1 units and cannot load ANY openwrt file, even with original FW back to 2.0.0. This is very frustrating and I am openly thinking about replacing the whole system (4x M3000, 1x AP3000 Out)… I need separate wireless networks and being limited to 2.4 and 5 is useless… I need a separate 2.4 network for IOT as well as a separate 5 network for IOT, a merged 2.4/5 for everything else and then a guest network…

Jon Fear

發表留言