警告
本網頁列出了支援OpenWrt系統的設備的軟體，在下載和安裝軟體之前，請注意OpenWrt Project是一個針對嵌入式設備的Linux作業系統。 OpenWrt 並沒有嘗試建立單一靜態韌體，而是提供了一個具有套件管理功能的完全可寫入檔案系統。這使您無需選擇供應商提供的應用程式和配置，並允許您透過使用軟體包來自訂設備以適應任何應用程式。對於開發人員來說，OpenWrt 是建立應用程式的框架，而無需圍繞它建立完整的韌體；對使用者來說，這意味著完全客製化的能力，以前所未有的方式使用裝置。
描述
- 此檔案僅當您的路由器在 Cudy Web UI 下運作時才能使用。
- 如果路由器已經在OpenWRT UI下工作，用戶應先將其恢復到Cudy官方韌體。然後用這個韌體升級路由器。
- 如何將路由器恢復至Cudy官方韌體？請閱讀下載文件中的自述文件。
保固：
Cudy特此聲明
- 我們 Cudy 對非深圳市 Cudy 科技有限公司發布的任何軟體不承擔任何保證。
- 對於安裝了非深圳市酷迪科技有限公司發布的任何軟體的產品，我們不承擔任何保證。
- 如果您需要使用openwrt軟體，建議您從Cudy官網下載。
下載 OpenWrt 韌體以刪除簽名檢查：驅動程式
OpenWrt 韌體查找器（不是由Cudy 發布）：OpenWrt 韌體選擇器
1319 則留言
Dear Cudy Support team!
Can I get firmware for install Openwrt on my router:
Model: WR3000E V2.0
Current Firmware: 2.4.18-20251124-103954
Маршрутизатор WR300 V1.0 SN:WR30002549
Прошивка 2.4.19-20250828-192837
Аппаратная версия WR3000 V1.0
Прошивка которая для WR3000 V1.0 на гугл диске не подходит. Выдает ошибку.
Просьба выслать прошивку по электронной почте
@Dear Dan,
Do you remember what is firmware version before update to the OpenWrt firmware? If it was 2.4.7, you can recover it via the TFTPD tool. Please refer to this article.
https://www.cudy.com/blogs/faq/how-to-recovery-the-cudy-router-from-openwrt-firmware-to-cudy-official-firmware?pos=1&_sid=b2bfff253&ss=r
If other firmware version, please keep using the OpenWrt firmware. Can not be recovered.
“Dear Cudy support team,
I am trying to restore the factory firmware after OpenWrt on AP3000 V1.0, but I am facing a problem.
Device information:
- Model: AP3000 V1.0
- Serial number: AP3000_P251600697 EU1.0
- Current firmware: OpenWrt 25.12.0
The problem is:
When trying to flash through the openwrt web interface (without saving the settings):
I downloaded the file “AP3000-R49-2.4.7-20260115-152710-sysupgrade.bin”, but the router rejects it with the error “Invalid file”.
According to the instructions for returning: Connected directly to a PC with IP:192.168.1.10, holding reset
Connected the power. But in this case, I can’t connect to the router. The special interface for specifying the firmware file doesn’t open at the address 192.168.1.1.
For the OpenWrt firmware, you provided a special firmware for the transition. I understand that you also need a special version to return to the factory firmware.
Please help me return to the factory firmware.
Thank you for your assistance. Best regards, Dan
"
@Dear Александр,
The OpenWrt firmware is not developed by Cudy but by the developers. We need the OpenWrt forum official support the router at first, then we can release a middle firmware for you, then you can use and upgrade to the OpenWrt firmware.
For WR3000 V2.0, it is impossible to develop the OpenWrt firmware currently.
“Please tell me when the OpenWRT firmware for WR3000 V2.0 will be available.”
@Dear Андрей,
I just uploaded the intermediate firmware for WR1300S V1.0 to the Google Drive. You can download it.
“When will there be an openwrt for WR1300S ? The kernel and sysupgrade were previously sent”