準備工作：
1.安裝天線並將其向上放置。
2.將 SIM 卡插入插槽，直到聽到喀嚓聲。
3.將電源供應器連接到路由器並開機。
第1 步：
開啟網頁瀏覽器並前往 http://cudy.net 或http://192.168.10.1。輸入管理員密碼進行登入。
注意：預設管理員密碼為"admin"，如果韌體版本為1.X.X。 自韌體版本 2.X.X 起，我們已刪除預設管理員密碼。首次登入時您必須設定管理員密碼。
有關詳細信息，請參閱如何登入Cudy Router的Web介面？ 第2 步： 將彈出"快速設定"窗口，選擇您的"時區"。
第 3 步：設定 APN 參數。大多數時候我們只需要將 APN 設定檔保持為"自動"。然後按一下"下一步"。路由器會自動選擇APN參數。 （建議） 如果您想自訂 APN 參數。您可以選擇 APN 設定檔為"手動"，並輸入正確的 APN 參數。 注意：如果您不確定 APN參數，請聯絡您的網際網路服務供應商。
第 4 步：更改無線網路名稱和密碼或保留預設值。
第5 步： 點選"儲存並套用"完成設定。 第6 步： 當狀態為已連接時，您可以享受網路。
52 則留言
@Dear Sakai,
You can set the metric of the WAN connection. The small the metric, the higher priority the WAN connection.
For the new firmware, it is under development currently. We will release a new firmware in the near future.
“R700 V1.0
I bought this router recently and this has never received any firmware update since its release date. Can you guys work on its latest firmware? Currently, we are unable to put multiple IP ranges when making a rule set to route specific data through a specific WAN.
Also, the rule is not applying properly sometimes. In the policy tab, you can not give priority to a specific WAN. Please fix these."
R700 V1.0
I bought this router recently and this has never received any firmware update since its release date. Can you guys work on its latest firmware? Currently, we are unable to put multiple IP ranges when making a rule set to route specific data through a specific WAN.
Also, the rule is not applying properly sometimes. In the policy tab, you can not give priority to a specific WAN. Please fix these.
@Dear Tommy,
Generally, there is no need to set the router. Just connect the devices to the LAN ports of the router. Then it will work. You can try to reset the router to factory default by long pressing the reset button for about 3 seconds. You can release the reset button when the LED flashes. Then connect all the devices and check if the problem avoided?
In addition, please check if the CCTV camera is set to get the IP address via DHCP when connect to the router via wired cable? If not, please set it.
“Dear Cudy team. How should I configure your router lt500D to be able to connect two CCTV cameras via Ethernet cable? I was able to connect only one that supports wifi, second one can be connected only via cable. Your router does not see these devices in lan network.”
Dear Cudy team. How should I configure your router lt500D to be able to connect two CCTV cameras via Ethernet cable? I was able to connect only one that supports wifi, second one can be connected only via cable. Your router does not see these devices in lan network.
@Dear Amigos,
The AT command for checking EARFCN is AT+QENG=“servingcell” , You can also check it in the syslog. For example
AT+QENG=“servingcell” → AT+QENG=“servingcell” +QENG: “servingcell”,“NOCONN”,“LTE”,“FDD”,250,01,41720C,9,1802,3,5,5,454C,-89,-10,-59,14,35 OK
The “1802” is the EARFCN.
For cell ID, we don’t have plan to change the format.
“Hi! In first iam need to say thanks for very balanced products with Cudy brand. Anyway i have some question about Cudy LT400 Outdoor functions.
1 – in Status we have data about LTE connection as MCC MNC CID and PCID, but not EARFCN and not eNodeB ID. How i can get it? Modem have this data by cell.
2- Cell ID have hex format. possible convert it in dec format Base ID?
and very important
need AT commands LIST for internal modem.
Thanks!"