WISP 模式：
在 WISP 模式下，路由器允許多個使用者共享 WISP 的網路連線。 LAN 埠設備透過無線連接埠與 WISP 共用相同的 IP。連接到WISP時，無線連接埠充當WAN連接埠。
常見網路拓樸：
第1 步： 開啟網路瀏覽器並前往 http://cudy.net 或 http://192.168.10.1.
詳情請參考 如何登入Cudy Router的Web介面？
第2 步： 將彈出快速設定窗口，選擇"WISP"，然後前往"下一步"。
第3 步： 選擇您的"時區"。
第4 步： 選擇您要擴充的主機網路。點選"連接"。
或點選 常規設定->WISP->啟用 然後選擇您要擴充的主機網路。
第5 步： 輸入主機網路的無線密碼。
注意： 請確保您輸入的無線密碼正確，否則設定無法成功。
第6 步： 自訂無線網路名稱和密碼或保留預設值。
第7 步： 點選"儲存並套用"完成設定。
第8 步： 等待幾秒鐘系統重新啟動，當再次彈出登入頁面時，您就可以享受網路了。
114 則留言
Hello Cudy Support. Could I also get please the beta version of Firmware supporting WISP work mode for the WR6500H router?
Thx
@Dear Peter Tomaščík,
Our technical support has sent you the firmware via email. Please check.
“I recently purchased the Cudy WR6500 as an upgrade to my older Cudy WR3000. My original plan was to use the new WR6500 as my main router and repurpose the WR3000 as a Mesh node to extend my network coverage.
However, I ran into a major issue: the WISP mode is missing in the WR6500 settings, whereas it works perfectly fine on the older WR3000.
Because the WR6500 lacks WISP support, I am currently forced to use it only as a Mesh extension instead of the main router, which completely degrades its performance and defeats the purpose of the upgrade.
Could the support team or anyone here provide me with a firmware version for the WR6500 that includes the WISP functionality?”
@Dear Lawson,
Please go to “General Settings” —"WISP " function page to set it up.
“I have the 4GvLTE N300 V3.0
I’ve got firmware 2.5.12 installed, but still no WISP
Could you send me the firmware that allows for Wisp please. I’m happy to test it if it’s Beta.”
@Dear John,
I think yes. WR1200 supports WISP function to connect the main Wi-Fi via wireless. But you must check if the signal strength starlink mini wifi router at the placement of WR1200 is powerful enough to connect to?
“Hi, can I use the wr1200 to feed wired internet into my lan from a starlink mini wifi router. I would like to not have a wire from the starlink into my existing lan which covers 4 floors of a concrete building. Is this compatible.
Thank you.”
I recently purchased the Cudy WR6500 as an upgrade to my older Cudy WR3000. My original plan was to use the new WR6500 as my main router and repurpose the WR3000 as a Mesh node to extend my network coverage.
However, I ran into a major issue: the WISP mode is missing in the WR6500 settings, whereas it works perfectly fine on the older WR3000.
Because the WR6500 lacks WISP support, I am currently forced to use it only as a Mesh extension instead of the main router, which completely degrades its performance and defeats the purpose of the upgrade.
Could the support team or anyone here provide me with a firmware version for the WR6500 that includes the WISP functionality?