什麼是存取點模式？ >
存取點模式是路由器使用與主路由器或數據機路由器的有線連接來擴展家庭網路的無線覆蓋範圍.< /span>
常見網路拓樸：
第 1 步：開啟網頁瀏覽器並造訪 http://cudy.net 或http://192.168.10.1。
詳情請參閱如何登入網頁介面Cudy 路由器？ >
第2 步： 將彈出"快速設定"窗口，選擇"無線存取點"，然後點選"下一步"< /strong> .
第 3 步： 選擇您的"時區"。
第 4 步：確認硬體連線。
第 5 步： 更改無線網路名稱和密碼。
第 6 步： 點選"儲存並套用"完成設定。
第7步： 等待幾秒鐘系統重新啟動，當再次彈出登入頁面時，您就可以享受網路了。
注意： 將Cudy路由器設定為Access Point模式後，IP位址將由主機路由器分配，預設IP位址192.168.10.1將無法登入。 "http://cudy.net/">http://cudy.net"，或在主（主）路由器的客戶端尋找Cudy 路由器的IP 位址清單。
24 則留言
@Werner
Dear Customer，
Thank you for contacting Cudy support team.
Please set the AP to static IP address, then reboot the main router, and check again.
“Hi, I have installed a Cudy 1300 Outdoor AP on a clients site, did the complete setup and as a wireless access point. I had set static ip address for the AP but werent internet connection through the AP, I then changed the AP’s ip setting to dhcp. On the status page it shows that the AP is connected to the internet via the lan cable but when I connect my laptop other device to the wifi its not getting internet access. Also cannot pin the gateway ip address from my laptop, but on the diagnostics page of the ap I can ping the gateway ip address. Can you please help with this, as I have a wireless camera connected to this AP but cannot access it from my lan.”
Hi, I have installed a Cudy 1300 Outdoor AP on a clients site, did the complete setup and as a wireless access point. I had set static ip address for the AP but werent internet connection through the AP, I then changed the AP’s ip setting to dhcp. On the status page it shows that the AP is connected to the internet via the lan cable but when I connect my laptop other device to the wifi its not getting internet access. Also cannot pin the gateway ip address from my laptop, but on the diagnostics page of the ap I can ping the gateway ip address. Can you please help with this, as I have a wireless camera connected to this AP but cannot access it from my lan.
@Steve,
Dear Customer,
Thank you for contacting Cudy support team. Please follow the steps:
1. Set the LAN IP address to the same subnet of the main router, it will be easy to login to the web page.
2. Set the WiFi SSID and password as you want.
3. Disable the DHCP server of the P5.
Then you can connect to the main router and use it as a AP.
“I have configured my P5 router, now I’d like to change it to Access Point. I can not see in the web interface any references at all to operation mode. How do I change the operation mode from wireless router to Access Point router?”
@Rafal,
Dear Customer,
Thank you for contacting Cudy support team.
Our technical support has sent you the solutions via email. Please check.
“Hi. I have an LT500 router upstairs with sim card and another downstairs connected in AP mode via ethernet cable to the 1st one due there is very little wifi signal coming between floors through the ceiling. It works well but results in 2 different wifi networks upstairs and downstairs. So when moving between rooms devices not always switch to the network with better signal. How to make it one network with same login and password on both floors? Is it possible to configure a mesh in this situation?”
I have configured my P5 router, now I’d like to change it to Access Point. I can not see in the web interface any references at all to operation mode. How do I change the operation mode from wireless router to Access Point router?