PoE 附件
乙太網路供電10

High-Speed/Long-Range/Daisy Chain

Connect Further. Deploy Flexibly.

Choose High-Speed mode to extend PoE by 100 m, or Long-Range mode to reach up to 250 m by limiting the speed to 10 Mbps. Need more distance and high speed? You can add up to three extenders in a daisy chain to achieve a total extension of 300 m.

High-Speed/Long-Range/Daisy Chain

Connect Further. Deploy Flexibly.

Choose High-Speed mode to extend PoE by 100 m, or Long-Range mode to reach up to 250 m by limiting the speed to 10 Mbps. Need more distance and high speed? You can add up to three extenders in a daisy chain to achieve a total extension of 300 m.

Built for Consistent Networking 24/7

Shields Against Static Discharge

Dry office environment may harm the client with static discharge, and POE10 is equipped with level 3 ESD protection, handling 6kV contact and 8kV air ESD.

Tri-Level Client Protections

Provide more reliable networking with short-circuit protection, overvoltage protection, and polarity protection.

High-Speed. Plug and Play.

Gigabit Speed

Provides super-fast bandwidth suitable for connecting multiple cameras, high-speed access points, speakers down the line. *Connecting mulitple clients requries additional network switch at its end.

Wall-Mount Ready

Installation is straightforward with no configuration required. Mounting screws are included in the box.

FAQ

  1. What is a PoE Extender?
    A PoE Extender allows you to extend both power and data over Ethernet beyond the standard 100 m (328 ft) limit. It receives PoE input from a PoE switch or injector and outputs power and data to the next device or another extender.
  2. Can I connect a PoE Extender directly to a non-PoE switch?
    No. A non-PoE switch does not provide power through Ethernet.
    You must use a PoE injector between the switch and the extender to supply power if you do not have a PoE switch.
  3. My PoE Extender is not working. What should I check first?
    Please verify the following:
  • The upstream device (switch or injector) supports PoE or PoE+ (802.3af/at).
  • Non-PoE switches cannot power the extender.
  • The Ethernet cable is Cat5e or higher, in good condition, and under 100 m per segment.
  • The total chain length (from the switch to the final device) does not exceed the maximum supported distance.
  • The powered device (PD), such as a camera or AP, does not exceed the extender’s PoE output capacity.
1 3

PoE 延長器

PoE 延長器, POE10 2.0

乙太網路供電10 2.0

PoE延長器，可將PoE距離延長100m。 

  • 千兆乙太網輸入, 千兆乙太網輸出
  • 802.3at/af 最大 30W 輸出 1
  • 802.3at/af 輸入
  • High-Speed/Long-Range Modes
  • High-Speed Extension up to 100 meters 2
  • 延長傳輸250米 3
  • 壁掛安裝
查看完整資訊
  1. The actual available power equals the uplink power minus the loss on the line and device’s own power consumption (see the power consumption in the spec sheet). A PoE switch or PoE adapter that supports standard IEEE PoE standard at 54 V is recommended as the uplink power source.
  2. 100m extension is measured from the GbE out to the client devices. The section between uplink switch and GbE In is determined by the uplink switch.
  3. The speed will be limited at 10 Mbps under the Extend/Long-Range mode.