警告
本網頁列出了支援OpenWrt系統的設備的軟體，在下載和安裝軟體之前，請注意OpenWrt Project是一個針對嵌入式設備的Linux作業系統。 OpenWrt 並沒有嘗試建立單一靜態韌體，而是提供了一個具有套件管理功能的完全可寫入檔案系統。這使您無需選擇供應商提供的應用程式和配置，並允許您透過使用軟體包來自訂設備以適應任何應用程式。對於開發人員來說，OpenWrt 是建立應用程式的框架，而無需圍繞它建立完整的韌體；對使用者來說，這意味著完全客製化的能力，以前所未有的方式使用裝置。
描述
- 此檔案僅當您的路由器在 Cudy Web UI 下運作時才能使用。
- 如果路由器已經在OpenWRT UI下工作，用戶應先將其恢復到Cudy官方韌體。然後用這個韌體升級路由器。
- 如何將路由器恢復至Cudy官方韌體？請閱讀下載文件中的自述文件。
保固：
Cudy特此聲明
- 我們 Cudy 對非深圳市 Cudy 科技有限公司發布的任何軟體不承擔任何保證。
- 對於安裝了非深圳市酷迪科技有限公司發布的任何軟體的產品，我們不承擔任何保證。
- 如果您需要使用openwrt軟體，建議您從Cudy官網下載。
下載 OpenWrt 韌體以刪除簽名檢查：驅動程式
OpenWrt 韌體查找器（不是由Cudy 發布）：OpenWrt 韌體選擇器
1530 則留言
@Dear Ivan,
Our technical support has sent you the firmware via email. Please check.
“Hi,
Could you provide the OpenWrt firmware for the M3000 using the Motorcomm YT8821 (Variant 2)?
Thank you and have a nice day :)”
@Hi Mikko，
Our technical support has sent you the firmware via email. Please check.
“Hey, could you send the Cudy signed openwrt firmware to WR3000 EU1.0? The file provided in the google drive gives error “File is invalid. Please retry.””
@Dear Ben Dover,
The router M3000 can not downgrade the firmware when installed Mesh system. Please power off other satellite Mesh routers. Then reset the M3000 to factory default. Then you can downgrade the firmware before installing mesh system.
“Hi,
I want to flash OpenWRT on an M3000 with a Motorcomm YT8821 (Variant 2). I downloaded your signed firmware from your Drive, but the file hash doesn’t match the one shown in the web application. Could you confirm if you have an up to date version available?
Thanks”
Hello.
I have a Cudy M3000 V2 EU2.0, board R37.
Hardware from system log:
NAND: GigaDevice F50L1G41LB
WAN PHY: Realtek RTL8221B
Stock firmware: 2.5.28
I downloaded the official intermediary package M3000 1.0_2.0.zip.
The included file:
cudy_m3000-v1-sysupgrade_20251119.bin
causes a boot loop after flashing. Ethernet continuously connects and disconnects.
I can restore the router successfully to stock firmware via TFTP, and it works normally again.
Could you please provide the correct OpenWrt intermediary firmware for my exact hardware revision?
Thank you.
I believe a very similar case has already occurred with the same or very similar hardware parameters — M3000 V2, board R37, F50L1G41LB NAND and RTL8221B PHY — where Cudy support provided a different intermediary firmware directly to the user.
If possible, please send me the same compatible intermediary firmware for this hardware revision instead of the public cudy_m3000-v1-sysupgrade_20251119.bin.
Hi,
Could you provide the OpenWrt firmware for the M3000 using the Motorcomm YT8821 (Variant 2)?
Thank you and have a nice day :)