1. 从这里下载并解压文件。
2. 从官方网站下载最新固件，并将其重命名为“recovery.bin”。注意：必须将其放在与 Tftpd 工具相同的文件夹中。
3. 关闭路由器电源。拔下电源适配器或按下电源按钮。
4. 使用以太网线将电脑连接到路由器的 LAN 端口。
注意：只有一款型号例外：TR1200。固件恢复期间必须连接 WAN 端口。其他所有型号均使用 LAN 端口。
5. 手动将计算机的 IP 地址配置为“192.168.1.88”。
6. 运行“ tftp32.exe ”。
7. 在命令行运行“ netsh advfirewall set allprofiles state off ”命令来禁用Windows防火墙，否则TFTP连接将被阻止。或者，您也可以在计算机的控制面板中禁用防火墙，如下所示。
8. 按住“重置”按钮/孔。在路由器通电之前以及TFTP开始下载固件之前，不要松开“重置”按钮/孔。
9. 打开路由器电源。
10. 当所有指示灯快速闪烁，或者 tftp 开始下载固件时，您可以松开“重置”按钮/孔。
11. 当指示灯缓慢闪烁时，升级完成。
12. 请将您电脑的 IP 地址恢复为动态 IP。
13. 完成。
242 条评论
Здравствуйте.
После попытки восстановления роутера M1800v2 на оригинальную прошивку роутер загружается, но при попытке входа я получаю форму ввода с подписью “Invalid board info”. Восстанавливал по tftp на прошивки M1800V2-R28-2.1.3-20240509-102323-flash.bin и M1800V2-R28-1.16.14-20231117-190903-flash.bin, разницы нет, эффект один и тот же. Как правильно откатиться на стоковую прошивку?
Спасибо.
PS: Если после восстановления подключить роутер не напрямую к компьютеру, а в локальную сеть, то при загрузке адрес 192.168.10.1 моргает и пропадает, а роутер получает IP-адрес от моего существующего роутера, но на на этом адресе нет открытых портов и в интерфейс попасть не получается. Wi-Fi сеть так же не включается.
@Dear Savva,
You can try to update the Cudy official firmware for your router again on the web page of your router. Then I think the problem will be solved.
“Good day. I was able to restore the firmware using these instructions, but when the router reboots, it resets the settings, and when connecting, I have to reset the password and run the setup wizard. I restored the firmware after using OpenWrt. What could be the cause and how can I fix it?”
Good day. I was able to restore the firmware using these instructions, but when the router reboots, it resets the settings, and when connecting, I have to reset the password and run the setup wizard. I restored the firmware after using OpenWrt. What could be the cause and how can I fix it?
@Dear Dany,
This is the correct article for recovering the router. You must connect the LAN port of the router to the computer when recovering. If you follow all the steps, but still don’t work. The uboot of the router may have been changed. Or the router is faulty. If you still can login to the web page of the router, you must change the uboot to Cudy official uboot first.
“Hello,
I am trying to reset and recover my Cudy TR30 router using TFTP64, but it does not work correctly.
When I connect the power and hold the RESET button, TFTP64 automatically switches the server interface to “Software Loopback Interface 1”. After that, nothing happens and the router does not start the recovery or firmware upload process.
I already tried:
Holding the RESET button before powering on Using different Ethernet ports Changing network adapter settings Setting a static IP address on my PC
However, the router still does not enter proper recovery mode.
Could you please help me understand:
1. How to correctly enter recovery/TFTP mode on the TR30
2. Which LAN port should be used
3. What IP settings are required
4. Whether this behavior indicates a hardware issue
Thank you."
Hello,
I am trying to reset and recover my Cudy TR30 router using TFTP64, but it does not work correctly.
When I connect the power and hold the RESET button, TFTP64 automatically switches the server interface to “Software Loopback Interface 1”. After that, nothing happens and the router does not start the recovery or firmware upload process.
I already tried:
Holding the RESET button before powering on Using different Ethernet ports Changing network adapter settings Setting a static IP address on my PCHowever, the router still does not enter proper recovery mode.
Could you please help me understand:
1. How to correctly enter recovery/TFTP mode on the TR30
2. Which LAN port should be used
3. What IP settings are required
4. Whether this behavior indicates a hardware issue
Thank you.