什么是接入点模式？
接入点模式是路由器使用有线连接到主路由器或调制解调器路由器来扩展家庭网络的无线覆盖范围。
常见网络拓扑：
步骤 1：打开网络浏览器并转到http://cudy.net或http://192.168.10.1 。
详细信息请参阅如何登录Cudy路由器的Web界面？
第 2 步：将弹出快速设置窗口，选择“无线接入点” ，然后单击“下一步” 。
步骤3：选择您的“时区” 。
步骤4：确认硬件连接。
第五步：更改无线网络名称和密码。
步骤6：点击“保存并应用”完成配置。
第七步：等待系统重新启动几秒钟，当再次弹出登录页面时，您就可以享受互联网了。
笔记：
将 Cudy 路由器设置为接入点模式后，IP 地址将由主路由器分配，默认 IP 地址 192.168.10.1 将无法登录。如果您需要再次登录 Cudy 路由器，请在浏览器中输入“ http://cudy.net”或在主路由器的客户端列表中查找 Cudy 路由器的 IP 地址。
60 条评论
@Dear Ben,
Please follow the steps:
1. Disconnect the cable of that connect the WAN port of the WR3000 to the main router. 2. Login to the web page of WR3000, Set it to Wireless Access Point mode.
3. Disable the DHCP server on the “Advanced Settings” page.
4. Connect the WR3000 to the LAN port of the main router.
Then check if the problem fixed?
Hi, recently bought the WR3000 and want to use it as access point. I can reach the internet with connected device while using the factory settings, but as soon as I do the quick setup it loses the connection to the internet router. The WR3000 and the internet router are connected by cable.
@Dear Emil,
Sorry to tell you that TR1200 is a 100Mbps ethernet port router. Can only support 100Mbps. It is not a gigabit ethernet port router.
“Hello, I bough the TR1200 travel router as an access point for my room, but after connecting it to my LAN wifi only reaches speeds of up to 75Mbps even though my Ethernet reaches up to a Gigabit per second on the same devices. The router is right beside the PC I’m testing on. The listing said it could reach speeds up to 867Mbps, could there be some sort of lock on my routing speed?”
Hello, I bough the TR1200 travel router as an access point for my room, but after connecting it to my LAN wifi only reaches speeds of up to 75Mbps even though my Ethernet reaches up to a Gigabit per second on the same devices. The router is right beside the PC I’m testing on. The listing said it could reach speeds up to 867Mbps, could there be some sort of lock on my routing speed?
@Dear Arnab,
Is your existing router a Cudy router which support Cudy mesh function? If yes, you can install mesh system with a new M1200 and your existing Cudy router via both Wired or Wireless backhaul. If not Cudy router, you can’t install mesh system with them. But you can connect the M1200 to your existing router via cable. You can also set the M1200 to WISP or Range Extender mode to connect to your existing router via Wi-Fi.
“Hello!
If I get an M1200 and want to set it up as an access point to my existing router, do I need to keep it connected to my existing router via LAN? Or I can set it up in a separate room from where my existing router is and it will act as a mesh?”