什么是接入点模式？
接入点模式是路由器使用有线连接到主路由器或调制解调器路由器来扩展家庭网络的无线覆盖范围。
常见网络拓扑：
步骤 1：打开网络浏览器并转到http://cudy.net或http://192.168.10.1 。
详细信息请参阅如何登录Cudy路由器的Web界面？
第 2 步：将弹出快速设置窗口，选择“无线接入点” ，然后单击“下一步” 。
步骤3：选择您的“时区” 。
步骤4：确认硬件连接。
第五步：更改无线网络名称和密码。
步骤6：点击“保存并应用”完成配置。
第七步：等待系统重新启动几秒钟，当再次弹出登录页面时，您就可以享受互联网了。
笔记：
将 Cudy 路由器设置为接入点模式后，IP 地址将由主路由器分配，默认 IP 地址 192.168.10.1 将无法登录。如果您需要再次登录 Cudy 路由器，请在浏览器中输入“ http://cudy.net”或在主路由器的客户端列表中查找 Cudy 路由器的 IP 地址。
30 条评论
Bonsoir a tous , j’espère que vous vous portez bien.
Au fait j’ai configuré mon antenne Cudy AC 1200 en mode point d’accès sans fil. Au début ça fonctionnait correctement, mais après une journée de fonctionnement, lorsque les clients essaie de se connecter, le portail captif de mon mikrotik au quel est connecté l’antenne ne s’affiche pas. Ç’est ma deuxième antenne qui fonctionne de cette manière. Vraiment j’ai besoin d’aide.
@Werner
Dear Customer，
Thank you for contacting Cudy support team.
Please set the AP to static IP address, then reboot the main router, and check again.
“Hi, I have installed a Cudy 1300 Outdoor AP on a clients site, did the complete setup and as a wireless access point. I had set static ip address for the AP but werent internet connection through the AP, I then changed the AP’s ip setting to dhcp. On the status page it shows that the AP is connected to the internet via the lan cable but when I connect my laptop other device to the wifi its not getting internet access. Also cannot pin the gateway ip address from my laptop, but on the diagnostics page of the ap I can ping the gateway ip address. Can you please help with this, as I have a wireless camera connected to this AP but cannot access it from my lan.”
Hi, I have installed a Cudy 1300 Outdoor AP on a clients site, did the complete setup and as a wireless access point. I had set static ip address for the AP but werent internet connection through the AP, I then changed the AP’s ip setting to dhcp. On the status page it shows that the AP is connected to the internet via the lan cable but when I connect my laptop other device to the wifi its not getting internet access. Also cannot pin the gateway ip address from my laptop, but on the diagnostics page of the ap I can ping the gateway ip address. Can you please help with this, as I have a wireless camera connected to this AP but cannot access it from my lan.
@Steve,
Dear Customer,
Thank you for contacting Cudy support team. Please follow the steps:
1. Set the LAN IP address to the same subnet of the main router, it will be easy to login to the web page.
2. Set the WiFi SSID and password as you want.
3. Disable the DHCP server of the P5.
Then you can connect to the main router and use it as a AP.
“I have configured my P5 router, now I’d like to change it to Access Point. I can not see in the web interface any references at all to operation mode. How do I change the operation mode from wireless router to Access Point router?”
@Rafal,
Dear Customer,
Thank you for contacting Cudy support team.
Our technical support has sent you the solutions via email. Please check.
“Hi. I have an LT500 router upstairs with sim card and another downstairs connected in AP mode via ethernet cable to the 1st one due there is very little wifi signal coming between floors through the ceiling. It works well but results in 2 different wifi networks upstairs and downstairs. So when moving between rooms devices not always switch to the network with better signal. How to make it one network with same login and password on both floors? Is it possible to configure a mesh in this situation?”