System Cudy Whole Home Mesh został zbudowany w celu wyeliminowania martwych stref i zapewnienia nieprzerwanego Wi-Fi w całym domu. W tym artykule krok po kroku dowiesz się, jak zbudować system siatkowy.
Przygotowanie:
1. Upewnij się, że posiadasz co najmniej 2 produkty Cudy.
2. Wszystkie produkty Cudy obsługują technologię siatkową: oficjalna strona internetowa Home Mesh-Cudy
3. Oprogramowanie sprzętowe jest aktualne: Centrum pobierania
4. Podczas konfiguracji zabierz je do tego samego pomieszczenia.
5. Zresetuj wszystkie produkty Cudy do ustawień fabrycznych. (Przy włączonym zasilaniu naciśnij i przytrzymaj przycisk RESET z szpilką przez 6 sekund, a następnie zwolnij.)
6. Skonfiguruj router główny i połącz go z Internetem.
Tutaj bierzemy M1800 i WR2100 jako przykłady:
Krok 1 : Otwórz przeglądarkę internetową i przejdź do http://cudy.net lub http://192.168.10.1 .
Aby uzyskać szczegółowe informacje, zobacz Jak zalogować się do interfejsu internetowego Cudy Router?
Krok 2 : Na stronie Stan systemu kliknij przycisk „+”.
Krok 3 : Naciśnij przycisk WPS na M1800, a następnie naciśnij przycisk WPS na WR2100.
Główna jednostka siatkowa: Flash biały
Dodatkowa jednostka siatkowa: Miga na przemian na biało i czerwono
Krok 4: Przejdź do „ Skanowanie ”, a następnie „ Łączenie ”.
Krok 5 : Poczekaj, aż dioda LED systemu dodatkowego routera zmieni kolor na niebieski, a następnie przenieś WR2100.
Krok 6 : Sukces i ciesz się siecią mesh.
Notatka:
1. Router 4/5G można skonfigurować wyłącznie jako główną jednostkę mesh. Na przykład:
2. Nie będziesz mógł zalogować się do interfejsu internetowego dodatkowego routera mesh. Jeśli chcesz zmienić ustawienia, kliknij „ Stan systemu ”->„ Siatka ”.
23 komentarze(-y)
@Владимир Владимир,
No, can not be used like this.
“Subject: Mesh Configuration with LT500 and WR1300 Routers
Dear Support Team,
I understand that the LT500 can only function as a main Mesh router and cannot be used as a satellite node.
I currently have three routers:
LT500
WR1300
LT500
Two of the LT500 units have access to the internet via 4G.
Is it possible to set up a Mesh network where all three devices are working together?
For example:
LT500 (main) + WR1300 (satellite)
The second LT500 (also with 4G) + the same WR1300 (as a satellite again)
In other words, can the same WR1300 be linked as a Mesh satellite to two separate LT500 routers?
Thank you for your assistance."
Subject: Mesh Configuration with LT500 and WR1300 Routers
Dear Support Team,
I understand that the LT500 can only function as a main Mesh router and cannot be used as a satellite node.
I currently have three routers:
LT500
WR1300
LT500
Two of the LT500 units have access to the internet via 4G.
Is it possible to set up a Mesh network where all three devices are working together?
For example:
LT500 (main) + WR1300 (satellite)
The second LT500 (also with 4G) + the same WR1300 (as a satellite again)
In other words, can the same WR1300 be linked as a Mesh satellite to two separate LT500 routers?
Thank you for your assistance.
@Tahseen,
We suggest 8 nodes.
“Hello, how many Cudy M3000 V2 AX3000 V2.0 https://www.cudy.com/products/m3000-2-0 can be used in a Mesh environment? Is there any threshold to signal strength (RSSI). Thanks, Tahseen”
@Andre van der weide,
Sorry for the inconvenience caused to you!
Please set the SSID of M3000 separately on 2.4GHz and 5GHz. Then connect to the 5GHz WiFi if the clients support 5GHz. The 2.4GHz is not as good as the 5GHz if the signal strength is weak.
“I have m3000 cudy mesh units i don’t know if version 1 ore 2.
5ghz working perfect but 2.4 mhz the network is sometimes found and connect but no internet connection. i have the latest firmware 2.3.8 on al 3 cudy’s
My wife get angry every time because no connection on phone and switching off wifi”
@Dear Fouad,
Yes, you can install mesh system with them via Wi-Fi or wired cable.
“I want to know if i buy 3x WR3000, if i can use them in MESH mode?”