Hoiatused
See veebileht loetleb OpenWrt süsteemi toetavate seadmete tarkvara, enne tarkvara allalaadimist ja paigaldamist palume arvestada, et OpenWrt Project on Linuxi operatsioonisüsteem, mis on suunatud manussüsteemidele. Selle asemel, et püüda luua üksikut staatilist püsivara, pakub OpenWrt täielikult kirjutatavat failisüsteemi koos paketihaldusega. See vabastab teid müüja poolt pakutavate rakenduste valikust ja konfiguratsioonist ning võimaldab teil kohandada seadet pakettide abil mis tahes rakendusele sobivaks. Arendajate jaoks on OpenWrt raamistik, mille abil saab luua rakenduse, ilma et oleks vaja ehitada selle ümber täielikku püsivara; kasutajate jaoks tähendab see võimalust täielikuks kohandamiseks, et kasutada seadet viisil, mida nad pole kunagi ette kujutanud.
Kirjeldus
- Seda faili saab kasutada ainult siis, kui teie ruuter töötab Cudy veebi kasutajaliidese all.
- Kui ruuter juba töötab OpenWRT UI all, peaks kasutaja esmalt taastama selle Cudy ametliku firmware'ile. Ja seejärel uuendada ruuterit selle püsivara abil.
- Kuidas taastada ruuter Cudy ametlikule püsivara? Palun lugege alla laaditud faili readme.
Garantii:
Cudy deklareerib käesolevaga
- Me, Cudy, ei võta garantiid ühegi tarkvara eest, mida ei ole välja andnud Shenzhen Cudy Technology Co., Ltd. .
- Me ei võta garantiid toodete eest, millele on paigaldatud tarkvara, mida ei ole välja andnud Shenzhen Cudy Technology Co., Ltd. .
- Kui teil on vaja kasutada openwrt tarkvara, soovitame selle alla laadida Cudy ametlikust veebisaidist.
Laadige alla OpenWrt püsivara, et eemaldada allkirja kontroll: Ajama
OpenWrt Firmware Finder (ei ole Cudy poolt välja antud): OpenWrt Firmware Selector
1530 kommentaari
@Dear enjoyer,
OK, We will check it
“Hello Cudy Support,
I have sent you this message as an email too.
My WR300 v1 bootloops after flashing the official OpenWrt intermediate
firmware (openwrt-ramips-mt76x8-cudy_wr300-squashfs-flash.bin). Stock firmware 2.5.24 works fine on this unit; the bootloop only starts after installing the
intermediate.
Serial number: S0000759261510557
Board marked as: 300100157 REV1.1
flash: cFeon QX64A-104HIP
Cause (from the UART boot log): this unit doesn’t recognize the flash chip
(JEDEC ID 1c 71 17). Newest firmware’s U-Boot recognizes it as `en25qx64a`,
but the kernel inside the intermediate (5.15.167, Sep 2024) has no driver
entry for it:
```
[ 0.350812] spi-nor spi0.0: unrecognized JEDEC id bytes: 1c 71 17 1c 71
17
[ 0.357913] spi-nor: probe of spi0.0 failed with error -2
…
[ 0.471677] Kernel panic – not syncing: VFS: Unable to mount root fs on
unknown-block(0,0)
```
Flashing the intermediate through tftp recovery also downgrades the
bootloader to an older U-Boot (Feb 11 2025) that prints
```
flash manufacture id: 1c, device id 71 17
Warning: un-recognized chip ID, please update bootloader!
```
Additionally, the TFTP recovery appears to only accept Cudy-signed images – an unsigned OpenWrt image passes the “R54” name check but is never flashed
(no “flash image / rsa verify” lines). So I could not install a patched
OpenWrt build myself;
I restored the router with the stock firmware via TFTP recovery and it
works again.
Could you please provide an updated intermediate firmware whose kernel
supports the EN25QX64A (1c 71 17)? A similar issue was fixed for the AX3000
series after its flash chip change.
Also, would you consider disabling RSA verification in the U-Boot TFTP
recovery, and/or providing a way to interrupt the U-Boot boot sequence to
reach a serial console? Otherwise an spi programmer adapter is required (like ch341a).
Thank you"
@Dear Alex,
Our technical support has sent you the firmware via email. Please check.
“Hello Cudy Support Team,
I have a Cudy WR3000 V1.0 (EU 1.0).
Current stock firmware:
2.4.19-20250828-192837
Serial number:
WR3000243506896
I would like to install official OpenWrt.
Please provide the latest Cudy-signed OpenWrt intermediate firmware compatible with my WR3000 V1.0 and my flash memory revision.
Thank you."
@Dear Henrique,
OK. Our technical support has sent you the firmware via email. Please check.
In addition, the firmware is in the Google Drive. I don’t know why you said this.
“Hi, I have a Cudy WR3000 EU 1.0 router with serial number starting with 2451 running firmware 2.2.6 US. I would like to install OpenWRT. Can you provide me the intermediate firmware for my device?
By the way, is there any reason not to have it available in the Google Drive folder along with the other models?"
I would like the Cudy-signed intermediary file for flashing my router with OpenWrt. What I have is Firmware Version 2.5.28-20260807-120317 and Hardware M3000 V2.0 with the YT8821 variant. Why is this file specifically not available on Google Drive where all the other files are?
TR3000-256MB EAEU1.0 — request for intermediate firmware and recovery file
Hello Cudy Support,
I sent this request to support@cudy.com on September 28 and again on September 29 (full S/N included in the emails), but have not received a reply yet, so I am posting here as well.
- Model: TR3000-256MB, EAEU1.0
- Production week in S/N: 2623
- Current stock firmware: 2.5.27-20260804-190139
I have NOT flashed anything yet. Another TR3000 256MB owner (S/N week 2626) reported on your recovery FAQ page on September 26 that the router stopped booting after flashing the intermediate firmware from the TR3000-256MB download page (DTS_and_intermediate_firmware, May 2025) on top of stock 2.5.21. My stock firmware is even newer and is not listed on the download page, so I want to confirm compatibility before flashing.
Could you please send me by email:
1. The intermediate firmware confirmed to work with my unit and stock 2.5.27.
2. The stock firmware for TFTP recovery (recovery.bin), ideally 2.5.27.
3. Which NAND flash chip is used in TR3000-256MB units from this batch.
4. Which OpenWrt image to install afterwards (cudy_tr3000-256mb-v1-squashfs-sysupgrade.bin from OpenWrt 25.12.x?).
Thank you!