1. Laadige fail alla ja pakendage see hinnast.
2. Laadige uusim püsivara ametlikust veebisaidist ja nimetage see ümber "recovery.bin". Märkus: Te peate selle panema samasse faili Tftpd tööriistade hulka.
3. Lülitage ruuter välja. Tõmmake toiteadapter välja või vajutage nuppu POWER.
4. Ühendage arvuti ruuteri LAN-porti Ethernet-kaabliga.
5. Konfigureerige oma arvuti IP-aadressi '192.168.1.88' käsitsi.
6. Käivitage 'tftp32.exe'.
7. Käivita käsureas 'netsh advfirewall set allprofiles state off', et keelata Windowsi tulemüür, muidu blokeeritakse tftp. Või lülitage tulemüür välja oma arvuti juhtpaneelis. Nagu allpool näidatud.
8. Vajutage nuppu/auku "Reset" ja hoidke seda all. Enne ruuteri sisselülitamist ja enne, kui tftp alustab püsivara allalaadimist, ärge vabastage nuppu 'Reset' / auku.
9. Lülitage ruuter sisse.
10. Kui kõik tuled vilguvad kiiresti või kui tftp hakkab püsivara alla laadima, võite vabastada nupu 'Reset' nuppu/auku.
11. Kui tuli vilgub aeglaselt, on uuendamine lõpetatud.
12. Taastage oma arvuti IP-aadress dünaamiliseks IP-ks.
13. Valmis.
242 comments
I have a cudy n700, it does not seem to reset or enter recovery mode, this is the second one with the same issue can you assist with resolving this urgently
@Dear Otis,
I think there is something wrong with the router. The router can’t be recovered.
“Hello , i have a CudyWR3000 and i wish to put it in recovery mode so that i can tftp my way into openwrt , the issue is , i can not put in recovery mode , i have tried holding the reset button while its unplugged and then plug it back in and keep holding for 12 seconds , at times even longer and no matter what i do , i do not get a rapidly blinking light indicating recovery mode , all i get is a steady power led and the internet led slowly blinking ( mind you when its in that mode which is not recovery no other light is on , just those two) . I thought that perhaps its recovery mode and i am missing something , i went on with the process the same way i would with it being in recovery , no matter how many times i tried or changes i made tcpdump indicated no request coming from the router .”
@Estimado Javier:
De acuerdo. Creo que está relacionado con el canal de trabajo. Algunos canales no admiten 160 MHz.
“He tenido que volver a las versión del Firmware original, ya que en Openwrt al configurar la Wifi 5G en ancho de banda 160 mhz, desparece y no se puede conectar. He hecho muchas pruebas y es cambiarlo a 80 mhz y si funciona. Este problema con el firm de Cudy no pasa. Se queda configurado en 160mhz y todo normal.”
Hello , i have a CudyWR3000 and i wish to put it in recovery mode so that i can tftp my way into openwrt , the issue is , i can not put in recovery mode , i have tried holding the reset button while its unplugged and then plug it back in and keep holding for 12 seconds , at times even longer and no matter what i do , i do not get a rapidly blinking light indicating recovery mode , all i get is a steady power led and the internet led slowly blinking ( mind you when its in that mode which is not recovery no other light is on , just those two) . I thought that perhaps its recovery mode and i am missing something , i went on with the process the same way i would with it being in recovery , no matter how many times i tried or changes i made tcpdump indicated no request coming from the router .
He tenido que volver a las versión del Firmware original, ya que en Openwrt al configurar la Wifi 5G en ancho de banda 160 mhz, desparece y no se puede conectar. He hecho muchas pruebas y es cambiarlo a 80 mhz y si funciona. Este problema con el firm de Cudy no pasa. Se queda configurado en 160mhz y todo normal.