1. Laadige fail alla ja pakendage see hinnast.
2. Laadige uusim püsivara ametlikust veebisaidist ja nimetage see ümber "recovery.bin". Märkus: Te peate selle panema samasse faili Tftpd tööriistade hulka.
3. Lülitage ruuter välja. Tõmmake toiteadapter välja või vajutage nuppu POWER.
4. Ühendage arvuti ruuteri LAN-porti Ethernet-kaabliga.
5. Konfigureerige oma arvuti IP-aadressi '192.168.1.88' käsitsi.
6. Käivitage 'tftp32.exe'.
7. Käivita käsureas 'netsh advfirewall set allprofiles state off', et keelata Windowsi tulemüür, muidu blokeeritakse tftp. Või lülitage tulemüür välja oma arvuti juhtpaneelis. Nagu allpool näidatud.
8. Vajutage nuppu/auku "Reset" ja hoidke seda all. Enne ruuteri sisselülitamist ja enne, kui tftp alustab püsivara allalaadimist, ärge vabastage nuppu 'Reset' / auku.
9. Lülitage ruuter sisse.
10. Kui kõik tuled vilguvad kiiresti või kui tftp hakkab püsivara alla laadima, võite vabastada nupu 'Reset' nuppu/auku.
11. Kui tuli vilgub aeglaselt, on uuendamine lõpetatud.
12. Taastage oma arvuti IP-aadress dünaamiliseks IP-ks.
13. Valmis.
249 comments
Hello , i have a CudyWR3000 and i wish to put it in recovery mode so that i can tftp my way into openwrt , the issue is , i can not put in recovery mode , i have tried holding the reset button while its unplugged and then plug it back in and keep holding for 12 seconds , at times even longer and no matter what i do , i do not get a rapidly blinking light indicating recovery mode , all i get is a steady power led and the internet led slowly blinking ( mind you when its in that mode which is not recovery no other light is on , just those two) . I thought that perhaps its recovery mode and i am missing something , i went on with the process the same way i would with it being in recovery , no matter how many times i tried or changes i made tcpdump indicated no request coming from the router .
He tenido que volver a las versión del Firmware original, ya que en Openwrt al configurar la Wifi 5G en ancho de banda 160 mhz, desparece y no se puede conectar. He hecho muchas pruebas y es cambiarlo a 80 mhz y si funciona. Este problema con el firm de Cudy no pasa. Se queda configurado en 160mhz y todo normal.
@Dear MD RAKIBUL ISLAM,
Yes, you can do it. This method also can recover the broken firmware issue.
“Hi Cudy, Can I follow all of these step to unbrick my Cudy WR1200 V2 which will be bricked due to sudden load shedding during firmware update 🙂? Please help”
Hi Cudy, Can I follow all of these step to unbrick my Cudy WR1200 V2 which will be bricked due to sudden load shedding during firmware update 🙂? Please help
@Dear Alan,
Please check if your use the correct firmware. You must use the firmware for TR3000 256MB, which the firmware version on Cudy official website is 2.3.9. Then you can follow the steps as the instruction.
“I am confident that it is the 256MB version because I purchased it from China, and the box, router, label, etc., all indicate “256MB.” However, when I opened the router, I discovered that the chip memory is ESMT F50L1G41LB only 128MB. You can check my post here: [https://www.right.com.cn/forum/thread-8441740-1-1.html] for a screenshot. I also sent this information to sales@cudy.com but haven’t received a reply.”