1. Laadige fail alla ja pakendage see hinnast.
2. Laadige uusim püsivara ametlikust veebisaidist ja nimetage see ümber "recovery.bin". Märkus: Te peate selle panema samasse faili Tftpd tööriistade hulka.
3. Lülitage ruuter välja. Tõmmake toiteadapter välja või vajutage nuppu POWER.
4. Ühendage arvuti ruuteri LAN-porti Ethernet-kaabliga.
5. Konfigureerige oma arvuti IP-aadressi '192.168.1.88' käsitsi.
6. Käivitage 'tftp32.exe'.
7. Käivita käsureas 'netsh advfirewall set allprofiles state off', et keelata Windowsi tulemüür, muidu blokeeritakse tftp. Või lülitage tulemüür välja oma arvuti juhtpaneelis. Nagu allpool näidatud.
8. Vajutage nuppu/auku "Reset" ja hoidke seda all. Enne ruuteri sisselülitamist ja enne, kui tftp alustab püsivara allalaadimist, ärge vabastage nuppu 'Reset' / auku.
9. Lülitage ruuter sisse.
10. Kui kõik tuled vilguvad kiiresti või kui tftp hakkab püsivara alla laadima, võite vabastada nupu 'Reset' nuppu/auku.
11. Kui tuli vilgub aeglaselt, on uuendamine lõpetatud.
12. Taastage oma arvuti IP-aadress dünaamiliseks IP-ks.
13. Valmis.
142 comments
@Ahmad,
Dear Customer,
Thank you for contacting Cudy support team.
Our technical support has contacted you via email. Please check.
“Hi, why I couldn’t download any files? got 404”
Hi, why I couldn’t download any files? got 404
@Alexander
Dear Customer,
Yes, you are right.
“OK, answer this myself (for TR3000 v1.0):
1. Find and download tftp32.exe
2. make directory “tftpboot”
3. put tftp32.exe AND the firmware (renamed to “recovery.bin”) into that directory
4. connect your PC to the LAN-port of the device
5. set your LAN IP to 192.168.1.88 like described here.
6. disable windows firewall (can do this with click and point in windows)
7. start tftp from the directory in step 2. and leave that window open
8. press reset-button on the device and then connect it to power/power on, keep pressed and wait, until it starts blinking/downloading the firmware to the device (in my case this was done after 3 seconds)
9. Enable firewall again, enable dynamic config (DHCP) on your lan port again, re-connect your lan and start to configure your Cudy device”
OK, answer this myself (for TR3000 v1.0):
1. Find and download tftp32.exe
2. make directory “tftpboot”
3. put tftp32.exe AND the firmware (renamed to “recovery.bin”) into that directory
4. connect your PC to the LAN-port of the device
5. set your LAN IP to 192.168.1.88 like described here.
6. disable windows firewall (can do this with click and point in windows)
7. start tftp from the directory in step 2. and leave that window open
8. press reset-button on the device and then connect it to power/power on, keep pressed and wait, until it starts blinking/downloading the firmware to the device (in my case this was done after 3 seconds)
9. Enable firewall again, enable dynamic config (DHCP) on your lan port again, re-connect your lan and start to configure your Cudy device
Sadly this does not work with my TR3000:
1. The download link (for tftp32?) is broken/does not work.
2. It doesn’t say where to put the sysupgrade firmware after download.
3. Does the sysupgrade firmware have to be renamed (to “recovery.bin”)?
Actually the stock vendor firmware for me is better/easier than open-wrt. So it should be possible to reflash to stock fw.