Cudy Whole Home Mesh system is built to eliminate dead zones and to provide uninterrupted Wi-Fi throughout your home. This article will guide you to build a mesh system step by step.
Preparation:
1. Ensure you own at least 2 Cudy products.
2. All Cudy products support mesh technology: Home Mesh-Cudy official website
3. Firmware is up-to-date: Download Center
4. Take them in the same room during configuration.
5. Reset all your Cudy products to factory default settings. (With the Power on, press and hold the RESET button with a pin for 6s, then release.)
6. Set up your primary router and make it connect to the internet.
Here we take M1800 and WR2100 as examples:
Step 1: Open a web browser and go to http://cudy.net or http://192.168.10.1.
For details, please refer to How to log into the web interface of Cudy Router?
Step 2: On the System Status page, click on the "+" button.
Step 3: Press the WPS button on the M1800 and then press the WPS button on WR2100.
Main mesh unit: Flash white
Add-on mesh unit: Flash white and red alternately
Step 4: It will go to "Scanning", then " Connecting".
Step 5: Wait until the System LED of the add-on router turns into solid blue, then relocate WR2100.
Step 6: Success and enjoy the mesh network.
Note:
1. 4/5G router can only be set up as a Main mesh unit. For example:
2. You will not able to log into the web interface of the add-on mesh router. If you want to change settings, please click on "System Status"->"Mesh".
90 comentarios
Thank you. How do I set the AX3000 , as wireless router , wireless acsess point ,wireless extender or WISP ?
@Dear Marc Pappin,
Yes, you can install mesh system with AP3000 and M3000. Please follow the steps:
1.Keep the three M3000 in the factory default status. Power them on next to the AP3000.
2. login to the webpage of AP3000, Click + to search the mesh nodes and then add all the three M3000 to be the satellite mesh nodes.
3. After mesh installed. You can move the three M3000 to the placement you want to place it.
“Hi, could I create a network, in the following sequence : AP3000, connected via a eth.cable to a non-cudy router . Router is connected via cable to WAN
After this proves to be stable I want to extend and create a mesh with 3 M3000 , all wireless.
Can the M3000 come off the AP3000, and if so how to set up and pair?
Thanks for your help"
@Dear Marc Pappin,
Yes, you can install mesh system with AP3000 and M3000. Please follow the steps:
1.Keep the three M3000 in the factory default status. Power them on next to the AP3000.
2. login to the webpage of AP3000, Click + to search the mesh nodes and then add all the three M3000 to be the satellite mesh nodes.
3. After mesh installed. You can move the three M3000 to the placement you want to place it.
“Hi, could I create a network, in the following sequence : AP3000, connected via a eth.cable to a non-cudy router . Router is connected via cable to WAN
After this proves to be stable I want to extend and create a mesh with 3 M3000 , all wireless.
Can the M3000 come off the AP3000, and if so how to set up and pair?
Thanks for your help"
Hi, could I create a network, in the following sequence : AP3000, connected via a eth.cable to a non-cudy router . Router is connected via cable to WAN
After this proves to be stable I want to extend and create a mesh with 3 M3000 , all wireless.
Can the M3000 come off the AP3000, and if so how to set up and pair?
Thanks for your help
@Dear Andy,
Yes, support. You can install mesh system with them.
“Are m3000 (ax3000) mesh unit compatible with later (BE11000 for example) mesh routers?”
Are m3000 (ax3000) mesh unit compatible with later (BE11000 for example) mesh routers?