警告
本網頁列出了支援OpenWrt系統的設備的軟體，在下載和安裝軟體之前，請注意OpenWrt Project是一個針對嵌入式設備的Linux作業系統。 OpenWrt 並沒有嘗試建立單一靜態韌體，而是提供了一個具有套件管理功能的完全可寫入檔案系統。這使您無需選擇供應商提供的應用程式和配置，並允許您透過使用軟體包來自訂設備以適應任何應用程式。對於開發人員來說，OpenWrt 是建立應用程式的框架，而無需圍繞它建立完整的韌體；對使用者來說，這意味著完全客製化的能力，以前所未有的方式使用裝置。
描述
- 此檔案僅當您的路由器在 Cudy Web UI 下運作時才能使用。
- 如果路由器已經在OpenWRT UI下工作，用戶應先將其恢復到Cudy官方韌體。然後用這個韌體升級路由器。
- 如何將路由器恢復至Cudy官方韌體？請閱讀下載文件中的自述文件。
保固：
Cudy特此聲明
- 我們 Cudy 對非深圳市 Cudy 科技有限公司發布的任何軟體不承擔任何保證。
- 對於安裝了非深圳市酷迪科技有限公司發布的任何軟體的產品，我們不承擔任何保證。
- 如果您需要使用openwrt軟體，建議您從Cudy官網下載。
下載 OpenWrt 韌體以刪除簽名檢查：驅動程式
OpenWrt 韌體查找器（不是由Cudy 發布）：OpenWrt 韌體選擇器
1319 則留言
@Dear Jaddie,
You can try to update back to older firmware first then try again. You can download the firmware 2.0.0 via the link.
https://www.cudy.com/en-us/pages/download-center/m3000-1-0
You can follow this instruction on the website to downgrade the firmware if you have installed mesh system with them.
https://www.cudy.com/en-us/blogs/faq/how-to-downgrade-the-firmware-to-the-older-version-of-mesh-system
Apologies, just checked and it actually just says the file is invalid, think the not applicable might have been when I was using openwrt’s file to see if it accepted it.
I am looking at trying to flash openwrt onto my cudy devices I have the M3000, one running
2.5.0-20260112-084313 and the other running 2.4.19-20250828-183718 it would be good to find out what is required to flash it onto them, as when I try it uploads the file initial file which I assume is meant to remove the signature checks, but it says the firmware is not applicable (presumably that firmware is out of date compared to what my devices already have on them) Is it possible to get an update version of the firmware to remove the sig check please?
@Dear Christian,
Our technical support has contacted you via email. Please check.
“I purchased six WR 3000 E for using them with OpenWRT. When I try to upload the cudy_wr3000e-v1-sysupgrade_20251119.bin from the Google Drive folder I get “Not applicable！Please upload the firmware applicable to the following models.”. The WR 3000 E is running 2.4.7 right now and the S/N is WR3000E24520. What am I doing wrong ? I really would like to run OpenWRT on the Cudys.”
I purchased six WR 3000 E for using them with OpenWRT. When I try to upload the cudy_wr3000e-v1-sysupgrade_20251119.bin from the Google Drive folder I get “Not applicable！Please upload the firmware applicable to the following models.”. The WR 3000 E is running 2.4.7 right now and the S/N is WR3000E24520. What am I doing wrong ? I really would like to run OpenWRT on the Cudys.