1. 从这里下载并解压文件。
2. 从官方网站下载最新固件，并将其重命名为“recovery.bin”。注意：必须将其放在与 Tftpd 工具相同的文件夹中。
3. 关闭路由器电源。拔下电源适配器或按下电源按钮。
4. 使用以太网线将电脑连接到路由器的 LAN 端口。
注意：只有一款型号例外：TR1200。固件恢复期间必须连接 WAN 端口。其他所有型号均使用 LAN 端口。
5. 手动将计算机的 IP 地址配置为“192.168.1.88”。
6. 运行“ tftp32.exe ”。
7. 在命令行运行“ netsh advfirewall set allprofiles state off ”命令来禁用Windows防火墙，否则TFTP连接将被阻止。或者，您也可以在计算机的控制面板中禁用防火墙，如下所示。
8. 按住“重置”按钮/孔。在路由器通电之前以及TFTP开始下载固件之前，不要松开“重置”按钮/孔。
9. 打开路由器电源。
10. 当所有指示灯快速闪烁，或者 tftp 开始下载固件时，您可以松开“重置”按钮/孔。
11. 当指示灯缓慢闪烁时，升级完成。
12. 请将您电脑的 IP 地址恢复为动态 IP。
13. 完成。
242 条评论
@Dear Alan,
Our technical support has contacted you via email. Please check.
“Thank you for your response. However, it did not resolve my issues.
Currently, my TR3000-256MB router when in a normal boot state. After plugging in the power cable, the red and white LEDs keep flashing, and my computer’s LAN connection is continuously going on and off. I attempted to set a static IP address of 192.168.1.2 on my computer, but I cannot ping or connect to the router’s webpage at 192.168.1.1.
When I try to use TFTP, the router does not respond to my computer’s IP (192.168.1.88), but it does respond to 192.168.1.2. After sending the recovery.bin file (downloaded from the mainland webpage: TR3000_256MB_Flash-R103-2.3.9-20250208-171917-sysupgrade.bin) to the router, it does not reboot on its own, and the LEDs continue to flash red and white.
The loop is continuous. Am I flashing the correct file? Is there any other way to restore the factory firmware?"
Thank you for your response. However, it did not resolve my issues.
Currently, my TR3000-256MB router when in a normal boot state. After plugging in the power cable, the red and white LEDs keep flashing, and my computer’s LAN connection is continuously going on and off. I attempted to set a static IP address of 192.168.1.2 on my computer, but I cannot ping or connect to the router’s webpage at 192.168.1.1.
When I try to use TFTP, the router does not respond to my computer’s IP (192.168.1.88), but it does respond to 192.168.1.2. After sending the recovery.bin file (downloaded from the mainland webpage: TR3000_256MB_Flash-R103-2.3.9-20250208-171917-sysupgrade.bin) to the router, it does not reboot on its own, and the LEDs continue to flash red and white.
The loop is continuous. Am I flashing the correct file? Is there any other way to restore the factory firmware?
@Dear Alan,
The LAN IP address will be changed from 192.168.10.1 to 192.168.1.1 after firmware update. You need to set the IP address to DHCP to get the IP address from the router.
You need to connect your computer to the LAN port of the router. Then try to login to the web page of the router via the IP address 192.168.1.1.
“Hi, I want to flash my TR300-256Mb router to OpenWrt, but after using the “cudy_tr3000-256mb-v1-sysupgrade.bin” file, it doesn’t display any pages upon reboot. The red and white LEDs keep flashing. I attempted to use TFTP for recovery, but unfortunately, I can’t revert to the original firmware. The same LED signal persists.
So, What can I do?”
Hi, I want to flash my TR300-256Mb router to OpenWrt, but after using the “cudy_tr3000-256mb-v1-sysupgrade.bin” file, it doesn’t display any pages upon reboot. The red and white LEDs keep flashing. I attempted to use TFTP for recovery, but unfortunately, I can’t revert to the original firmware. The same LED signal persists.
So, What can I do?
Figured out my problem – I was using a long cellphone SIM tray removal tool, and at that angle, it was slipping off the reset button and I did not realize it.
Use my smallest allen key that I could put a lot better pressure on and with worked perfectly, on 2 different WR3000Hs.
Also, downloaded the latest version of the 64-bit tftpd and tested, and it still works perfectly fine, too.
Once I got it to work, I see also that it is very fast – took no more than maybe 2 minutes from start to fully usable Cudy interface.
Thanks!