1. 从这里下载并解压文件。
2. 从官方网站下载最新固件，并将其重命名为“recovery.bin”。注意：必须将其放在与 Tftpd 工具相同的文件夹中。
3. 关闭路由器电源。拔下电源适配器或按下电源按钮。
4. 使用以太网线将电脑连接到路由器的 LAN 端口。
注意：只有一款型号例外：TR1200。固件恢复期间必须连接 WAN 端口。其他所有型号均使用 LAN 端口。
5. 手动将计算机的 IP 地址配置为“192.168.1.88”。
6. 运行“ tftp32.exe ”。
7. 在命令行运行“ netsh advfirewall set allprofiles state off ”命令来禁用Windows防火墙，否则TFTP连接将被阻止。或者，您也可以在计算机的控制面板中禁用防火墙，如下所示。
8. 按住“重置”按钮/孔。在路由器通电之前以及TFTP开始下载固件之前，不要松开“重置”按钮/孔。
9. 打开路由器电源。
10. 当所有指示灯快速闪烁，或者 tftp 开始下载固件时，您可以松开“重置”按钮/孔。
11. 当指示灯缓慢闪烁时，升级完成。
12. 请将您电脑的 IP 地址恢复为动态 IP。
13. 完成。
249 条评论
Hello,
I’m trying to revert my AP3000 v1 to the OEM firmware, but it won’t enter recovery mode or download the firmware from the TFTP server.
When I power on the access point while holding the reset button, the red and yellow LEDs blink alternately at regular intervals.
Could you please help me understand what this indicates or how to properly restore the OEM firmware?
Thank you!
@Caro Marco,
il nostro supporto tecnico ti ha contattato via e-mail. Ti preghiamo di controllare.
“Buongiorno ho un modem cudy p5 5g da quando ho fatto aggiornamento a settembre2025 non si connette in 5g rimane solo 4g che posso fare?”
I have a cudy n700, it does not seem to reset or enter recovery mode, this is the second one with the same issue can you assist with resolving this urgently
@Dear Otis,
I think there is something wrong with the router. The router can’t be recovered.
“Hello , i have a CudyWR3000 and i wish to put it in recovery mode so that i can tftp my way into openwrt , the issue is , i can not put in recovery mode , i have tried holding the reset button while its unplugged and then plug it back in and keep holding for 12 seconds , at times even longer and no matter what i do , i do not get a rapidly blinking light indicating recovery mode , all i get is a steady power led and the internet led slowly blinking ( mind you when its in that mode which is not recovery no other light is on , just those two) . I thought that perhaps its recovery mode and i am missing something , i went on with the process the same way i would with it being in recovery , no matter how many times i tried or changes i made tcpdump indicated no request coming from the router .”
@Estimado Javier:
De acuerdo. Creo que está relacionado con el canal de trabajo. Algunos canales no admiten 160 MHz.
“He tenido que volver a las versión del Firmware original, ya que en Openwrt al configurar la Wifi 5G en ancho de banda 160 mhz, desparece y no se puede conectar. He hecho muchas pruebas y es cambiarlo a 80 mhz y si funciona. Este problema con el firm de Cudy no pasa. Se queda configurado en 160mhz y todo normal.”