1. 从这里下载并解压文件。
2. 从官网下载最新固件，并将其重命名为“recovery.bin”。注意：必须将其与Tftpd工具放在同一个文件中。
3. 关闭路由器。拔下电源适配器或按下电源按钮。
4. 使用以太网电缆将您的计算机连接到路由器的 LAN 端口。
5.手动将计算机的IP地址配置为“192.168.1.88”。
6. 运行‘ tftp32.exe ’。
7. 在命令行中运行“ netsh advfirewall set allprofiles state off ”以禁用 Windows 防火墙，否则 TFTP 将被阻止。或者，您也可以在计算机的“控制面板”中禁用防火墙。如下所示。
8. 按住“ Reset ”按钮/孔。在路由器通电前以及TFTP开始下载固件前，请勿松开“ Reset ”按钮/孔。
9. 打开路由器电源。
10.当所有灯都快速闪烁时，或者当 tftp 开始下载固件时，您可以松开“重置”按钮/孔。
11.当灯光慢闪时，升级完成。
12.请将您计算机的IP地址恢复为动态IP。
13.完成。
143 条评论
Hello
For Cudy X6 V2, I am having the same issue – invalid board info.
It doesnot allow any login or setup(effectively bricking the router).
Can you please outline the steps to recover from this situation.
Thank you
Dear Customer,
Thank you for contacting Cudy support team.
Our technical support has contacted you via email. Please check.
“Greetings, I possess a Cudy X6 V2 router operating on OpenWrt, and I wish to revert to the official Cudy firmware. I followed your instructions to return to Cudy’s firmware, i.e. to go from OpenWRT Firmware back to Cudy’s Official Firmware. After i flashed successfully with tftp32 the newest official firmware for the cudy x6 v2 (x6v2-R30-2.1.0-20240411-114110), I get “invalid board info” error at the device login page (192.168.10.1 or cudy.net) where one needs to create a new admin password. The website-header also reads a strange “lede” title. What does the “Invalid board info!” error mean and how can it be fixed? kind regards!”
Greetings, I possess a Cudy X6 V2 router operating on OpenWrt, and I wish to revert to the official Cudy firmware. I followed your instructions to return to Cudy’s firmware, i.e. to go from OpenWRT Firmware back to Cudy’s Official Firmware. After i flashed successfully with tftp32 the newest official firmware for the cudy x6 v2 (x6v2-R30-2.1.0-20240411-114110), I get “invalid board info” error at the device login page (192.168.10.1 or cudy.net) where one needs to create a new admin password. The website-header also reads a strange “lede” title. What does the “Invalid board info!” error mean and how can it be fixed? kind regards!
@Ahmad,
Dear Customer,
Thank you for contacting Cudy support team.
Our technical support has contacted you via email. Please check.
“Please, contact me. I did all the steps and was unable to repair my Cudy wr1300. It’s seems that the firmware was successfully installed on the router but this did not change anything. I still have not gotten an IP address”
Please, contact me. I did all the steps and was unable to repair my Cudy wr1300. It’s seems that the firmware was successfully installed on the router but this did not change anything. I still have not gotten an IP address