1. 从这里下载并解压文件。
2. 从官网下载最新固件，并将其重命名为“recovery.bin”。注意：必须将其与Tftpd工具放在同一个文件中。
3. 关闭路由器。拔下电源适配器或按下电源按钮。
4. 使用以太网电缆将您的计算机连接到路由器的 LAN 端口。
5.手动将计算机的IP地址配置为“192.168.1.88”。
6. 运行‘ tftp32.exe ’。
7. 在命令行中运行“ netsh advfirewall set allprofiles state off ”以禁用 Windows 防火墙，否则 TFTP 将被阻止。或者，您也可以在计算机的“控制面板”中禁用防火墙。如下所示。
8. 按住“ Reset ”按钮/孔。在路由器通电前以及TFTP开始下载固件前，请勿松开“ Reset ”按钮/孔。
9. 打开路由器电源。
10.当所有灯都快速闪烁时，或者当 tftp 开始下载固件时，您可以松开“重置”按钮/孔。
11.当灯光慢闪时，升级完成。
12.请将您计算机的IP地址恢复为动态IP。
13.完成。
142 条评论
@Уважаемый Павел,
Какая прошивка у вашего Cudy TR30 (TR3000)? Это последняя версия прошивки 2.4.7? Если нет, пожалуйста, сначала обновите прошивку. Затем проверьте еще раз.
“Здравствуйте! При подключении к Cudy TR30 (TR3000) LTE модема, нет соединения. В настройках Cudy USB соединение неактивно. Что можно сделать?”
@Dear Alan,
So, why do you think it is the 256MB version. The 256MB version is only available for sell in China. The words on the label are in Chinese language, please have a check.
“Regarding the previous issue (failure to recover TR3000-256MB), I was finally able to revive it from being bricked using TTL. My router itself has no any hardware faults. I discovered that the NAND chip’s memory size differs from what is indicated on the box or label. This mismatch led to flashing the wrong version, causing it to become bricked and continuously reboot.
The chip inside is an ESMT F50L1G41LB, which can be broken down as follows:
F – Manufacturer: ESMT 50 – Product Collection L – Low Voltage (DDR3L) 1G – Density: 1Gb (Single Capacity) 41 – Organizational Structure: x16 (16-bit wide) LB – Packages and Versions
The capacity of a single unit is calculated as follows:
1Gb ÷ 8 bits/byte = 128MB
I hope you all don’t have to deal with the same issue I experienced. I’ve reached out to sales@cudy.com but haven’t received a response yet."
Здравствуйте! При подключении к Cudy TR30 (TR3000) LTE модема, нет соединения. В настройках Cudy USB соединение неактивно. Что можно сделать?
Regarding the previous issue (failure to recover TR3000-256MB), I was finally able to revive it from being bricked using TTL. My router itself has no any hardware faults. I discovered that the NAND chip’s memory size differs from what is indicated on the box or label. This mismatch led to flashing the wrong version, causing it to become bricked and continuously reboot.
The chip inside is an ESMT F50L1G41LB, which can be broken down as follows:
F – Manufacturer: ESMT 50 – Product Collection L – Low Voltage (DDR3L) 1G – Density: 1Gb (Single Capacity) 41 – Organizational Structure: x16 (16-bit wide) LB – Packages and VersionsThe capacity of a single unit is calculated as follows:
1Gb ÷ 8 bits/byte = 128MB
I hope you all don’t have to deal with the same issue I experienced. I’ve reached out to sales@cudy.com but haven’t received a response yet.
@Уважаемый Павел,
Пожалуйста, следуйте этой инструкции шаг за шагом. Если это не поможет, попробуйте выполнить эту операцию на другом компьютере.
“Здравствуйте! После прошивки роутера Cudy TR30 (TR3000) на OpenWRT решил прошить на заводскую прошивку и видимо бэкап не прошился. Теперь роутер не загружается и не заходит в web панель управления. Как можно это исправить?”