WISP 模式：
在 WISP 模式下，路由器允许多个用户共享来自 WISP 的互联网连接。以这种方式，LAN 端口设备通过无线端口共享来自 WISP 的相同 IP。当连接到 WISP 时，无线端口用作 WAN 端口。
常见网络拓扑：
步骤 1： 打开 Web 浏览器并转到 http://cudy.net 或者 http://192.168.10.1 。
详情请参阅 如何登录 Cudy Router 的 Web 界面？
第 2 步： 将弹出快速设置窗口，选择“ WISP ”，然后转到“下一步”。
步骤3： 选择您的“时区”。
步骤4： 选择要扩展的主机网络。单击“连接” 。
或点击 常规设置-> WISP ->启用 然后选择要扩展的主机网络。
步骤5： 输入主机网络的无线密码。
笔记： 请确保您输入的无线密码正确，否则配置无法成功。
第 6 步： 自定义无线网络名称和密码或保持默认。
步骤7： 单击“保存并应用”完成配置。
步骤8： 等待系统重新启动几秒钟，当再次弹出登录页面时，您就可以享受互联网了。
114 条评论
Hello Cudy Support. Could I also get please the beta version of Firmware supporting WISP work mode for the WR6500H router?
Thx
@Dear Peter Tomaščík,
Our technical support has sent you the firmware via email. Please check.
“I recently purchased the Cudy WR6500 as an upgrade to my older Cudy WR3000. My original plan was to use the new WR6500 as my main router and repurpose the WR3000 as a Mesh node to extend my network coverage.
However, I ran into a major issue: the WISP mode is missing in the WR6500 settings, whereas it works perfectly fine on the older WR3000.
Because the WR6500 lacks WISP support, I am currently forced to use it only as a Mesh extension instead of the main router, which completely degrades its performance and defeats the purpose of the upgrade.
Could the support team or anyone here provide me with a firmware version for the WR6500 that includes the WISP functionality?”
@Dear Lawson,
Please go to “General Settings” —"WISP " function page to set it up.
“I have the 4GvLTE N300 V3.0
I’ve got firmware 2.5.12 installed, but still no WISP
Could you send me the firmware that allows for Wisp please. I’m happy to test it if it’s Beta.”
@Dear John,
I think yes. WR1200 supports WISP function to connect the main Wi-Fi via wireless. But you must check if the signal strength starlink mini wifi router at the placement of WR1200 is powerful enough to connect to?
“Hi, can I use the wr1200 to feed wired internet into my lan from a starlink mini wifi router. I would like to not have a wire from the starlink into my existing lan which covers 4 floors of a concrete building. Is this compatible.
Thank you.”
I recently purchased the Cudy WR6500 as an upgrade to my older Cudy WR3000. My original plan was to use the new WR6500 as my main router and repurpose the WR3000 as a Mesh node to extend my network coverage.
However, I ran into a major issue: the WISP mode is missing in the WR6500 settings, whereas it works perfectly fine on the older WR3000.
Because the WR6500 lacks WISP support, I am currently forced to use it only as a Mesh extension instead of the main router, which completely degrades its performance and defeats the purpose of the upgrade.
Could the support team or anyone here provide me with a firmware version for the WR6500 that includes the WISP functionality?