Cudy Whole Home Mesh 系统旨在消除死角，并为您的整个家庭提供不间断的 Wi-Fi。本文将指导您逐步构建网状系统。
准备：
1. 确保您拥有至少 2 件 Cudy 产品。
2.Cudy所有产品均支持mesh技术：首页Mesh-Cudy官网
3. 固件已更新：下载中心
4. 配置时将它们放在同一个房间。
5. 将所有 Cudy 产品重置为出厂默认设置。（打开电源后，用别针按住 RESET 按钮 6 秒钟，然后松开。）
6. 设置您的主路由器并使其连接到互联网。
这里我们以M1800和WR2100为例：
步骤 1 ：打开网络浏览器并转到http://cudy.net或http://192.168.10.1 。
详细信息请参阅如何登录Cudy路由器的Web界面？
第 2 步：在系统状态页面，单击“+”按钮。
步骤 3 ：按下 M1800 上的 WPS 按钮，然后按下 WR2100 上的 WPS 按钮。
主网单元：闪光白
附加网格单元：白色和红色交替闪烁
步骤 4：它将进入“扫描”，然后进入“连接”。
步骤 5 ：等到附加路由器的系统 LED 变为常亮蓝色，然后重新定位 WR2100。
步骤 6 ：成功并享受网状网络。
笔记：
1. 4/5G 路由器只能设置为主网状单元。例如：
2. 您将无法登录附加网状路由器的 Web 界面。如果您要更改设置，请点击“系统状态”->“ Mesh ”。
83 条评论
@Dear John,
1. Please check if the Mesh system is installed. You can login to the web page of the main mesh router, check the “Mesh” status card.
2. If yes, please check the status page of the satellite mesh router. Check if the backhaul is Wired?
3. If the backhaul is wired, please try to change the cable between the two router. Do you connect them directly or there is a switch between them?
4. What is the firmware version of the two routers? Please update to the latest and check again.
“I have two WR11000s which I’m trying to use as a mesh. The main router is connected to 1 Gbps fibre WAN. The secondary router is connected to the main router by wired ethernet (cat 6 cable).
When I plug my laptop into the secondary router with ethernet, I get a great connection (~800+ Mbps, according to speedtest.net). When I connect to the secondary router by wifi, the connection is hopeless — even sitting my laptop right next to the router, I get speeds of just a couple of Mbps, and lots of drop outs. This happens on all bands (2/5/6 GHz).
When I am connected to the main router by wifi, it works fine.
Any suggestions as to what might be going wrong?
Thanks!"
I have two WR11000s which I’m trying to use as a mesh. The main router is connected to 1 Gbps fibre WAN. The secondary router is connected to the main router by wired ethernet (cat 6 cable).
When I plug my laptop into the secondary router with ethernet, I get a great connection (~800+ Mbps, according to speedtest.net). When I connect to the secondary router by wifi, the connection is hopeless — even sitting my laptop right next to the router, I get speeds of just a couple of Mbps, and lots of drop outs. This happens on all bands (2/5/6 GHz).
When I am connected to the main router by wifi, it works fine.
Any suggestions as to what might be going wrong?
Thanks!
@Dear Kamil,
I think the camera is connected to the 2.4GHz WiFi of the router. You can try to change the mode of 2.4GHz to 802.11b+g+n mode. Then check if the camera is able to connect to it?
“I built a mesh network using four WR3600E routers, and the internet works great. However, this network was meant for cctv monitoring, and that’s where the problem appeared: when the routers are in mesh mode, the cameras won’t log into the network, no matter which WPA level we choose. Only after disabling encryption and the password do the cameras connect to Wi-Fi. The cameras are XMeye. Is there any solution? When connected to lan port everything works. I’ll add that when the router is not in mesh mode, the same camera connects to it normally with wifi. Regards.”
I built a mesh network using four WR3600E routers, and the internet works great. However, this network was meant for cctv monitoring, and that’s where the problem appeared: when the routers are in mesh mode, the cameras won’t log into the network, no matter which WPA level we choose. Only after disabling encryption and the password do the cameras connect to Wi-Fi. The cameras are XMeye. Is there any solution? When connected to lan port everything works. I’ll add that when the router is not in mesh mode, the same camera connects to it normally with wifi. Regards.
@Dear Paweł,
Yes, you can. You can choose on of the M3000 to be the main mesh device. Then set it to working on the Mesh Access Point mode. Connect it to the network. Then reset all other Cudy devices to factory default. For the second M3000, please connect to the WAN port to the network. For the APs, please connect to the network directly. The Mesh system will be install automatically.
“Hi,
I have no cudy router as my main router, I’m going to disable wifi on that router and cerate mesh system viavwired backhaul. can I connect via eth 2 cudy m3000 and 2 ap3000 and cerate wired mesh between them with having fast roaming without creating subnet.”