Cudy Whole Home Mesh 系统旨在消除死角，并为您的整个家庭提供不间断的 Wi-Fi。本文将指导您逐步构建网状系统。
准备：
1. 确保您拥有至少 2 件 Cudy 产品。
2.Cudy所有产品均支持mesh技术：首页Mesh-Cudy官网
3. 固件已更新：下载中心
4. 配置时将它们放在同一个房间。
5. 将所有 Cudy 产品重置为出厂默认设置。（打开电源后，用别针按住 RESET 按钮 6 秒钟，然后松开。）
6. 设置您的主路由器并使其连接到互联网。
这里我们以M1800和WR2100为例：
步骤 1 ：打开网络浏览器并转到http://cudy.net或http://192.168.10.1 。
详细信息请参阅如何登录Cudy路由器的Web界面？
第 2 步：在系统状态页面，单击“+”按钮。
步骤 3 ：按下 M1800 上的 WPS 按钮，然后按下 WR2100 上的 WPS 按钮。
主网单元：闪光白
附加网格单元：白色和红色交替闪烁
步骤 4：它将进入“扫描”，然后进入“连接”。
步骤 5 ：等到附加路由器的系统 LED 变为常亮蓝色，然后重新定位 WR2100。
步骤 6 ：成功并享受网状网络。
笔记：
1. 4/5G 路由器只能设置为主网状单元。例如：
2. 您将无法登录附加网状路由器的 Web 界面。如果您要更改设置，请点击“系统状态”->“ Mesh ”。
83 条评论
@Dear Oli,
Cudy AP1300 can only install mesh system with Cudy product. If the speed is slow, may be there is some limit on the main router. You can try to set it to the Wireless Router mode and check.
“Recently installed an AP1300 in AP mode. Served via CAT 7 ethernet cable attached to the main internet router of the Internet Provider (diffrent brand). DIdn’t realize, that mesh is default while AP mode setup of the cudy. May mesh disturb, i.e. slow down connection of attached devices?”
Recently installed an AP1300 in AP mode. Served via CAT 7 ethernet cable attached to the main internet router of the Internet Provider (diffrent brand). DIdn’t realize, that mesh is default while AP mode setup of the cudy. May mesh disturb, i.e. slow down connection of attached devices?
@Dear Gabriel,
Basically, this is a hardware issue. May be caused by the cable or the router. We can have a compare test. You can choose one of the other two routers, Reset it and set it to be the main mesh router and connect to the same cable to check if it work on 1 Gbps or 100Mbps to judge the root cause.
“Dear Cudy Support,
I recently purchased a Cudy AX3000 Gigabit WiFi 6 Mesh Router along with two additional AX3000 mesh units, all of which support gigabit Ethernet ports.
My internet plan provides 200Mbps, and I am using undamaged Cat 6 Ethernet cables. The main router is connected to one of the mesh nodes via Ethernet. Up until yesterday, everything was working perfectly—I was getting full gigabit speeds through the LAN ports.
However, after rebooting the entire system today, the main router’s Ethernet ports are now only delivering 100Mbps. I’ve confirmed that the cables are properly seated and not damaged, and the same setup was previously delivering full gigabit speeds without issue.
Could you assist in identifying what might have caused this and how to resolve it?
Thank you"
Dear Cudy Support,
I recently purchased a Cudy AX3000 Gigabit WiFi 6 Mesh Router along with two additional AX3000 mesh units, all of which support gigabit Ethernet ports.
My internet plan provides 200Mbps, and I am using undamaged Cat 6 Ethernet cables. The main router is connected to one of the mesh nodes via Ethernet. Up until yesterday, everything was working perfectly—I was getting full gigabit speeds through the LAN ports.
However, after rebooting the entire system today, the main router’s Ethernet ports are now only delivering 100Mbps. I’ve confirmed that the cables are properly seated and not damaged, and the same setup was previously delivering full gigabit speeds without issue.
Could you assist in identifying what might have caused this and how to resolve it?
Thank you
@Dear Walter,
Yes, you can. The Cudy APs, such as the AP3000 and AP1300 can work as the main mesh device to manage other APs. You can set up one of the AP3000 and connect it to the network. Then connect other AP to the network. The mesh system will be installed automatically.
“Can I set up a mesh network using only Cudy AP’s? I have a different brand router so I want to build a mesh network with just the AP’s”