C200P 工作模式和拓扑结构

C200P 是一款功能全面的网络设备，集成了路由器和 AP 控制器功能，提供两种工作模式：主路由器和 AP 控制器（默认）以及AP 控制器模式。本指南提供设置说明和网络拓扑建议，以实现最佳性能。

1. 主路由器和AP控制器（默认）

在这种模式下，C200P 同时充当路由器和 AP 控制器。
建议管理≤10个AP和≤100个客户端。

拓扑结构 1：互联网 - C200P - 交换机 - AP

  • 使用场景：适用于管理多个 AP（需要交换机来扩展端口容量）。
  • 设置要求：
    • 将调制解调器连接到 C200P 的 WAN 端口，将 C200P 的 LAN 端口连接到交换机，再将 AP 连接到交换机。
    • 确保 C200P 和 AP 处于同一 VLAN中，因为 AP 管理流量不携带 VLAN 标签。
  • SSID VLAN 支持：
    • 启用 SSID VLAN 将使客户端数据在从 AP 发送出去时携带 VLAN 标签。
    • C200P 不支持 VLAN 或 VLAN 接口。
    • 要启用 SSID VLAN，交换机必须支持 VLAN、VLAN 接口和 DHCP 服务器，以便为 SSID VLAN 中的无线客户端分配 IP 地址。

拓扑结构 2：互联网 - C200P - AP

  • 使用场景：适用于≤4 个 AP的小型网络（受限于 C200P 的 4 个 LAN 端口）。
  • 设置要求：
    • 将调制解调器连接到 C200P 的 WAN 端口，将 AP 直接连接到 C200P 的 LAN 端口。
    • C200P、AP 和无线客户端在同一网络中运行。
  • SSID VLAN 支持：
    • 此拓扑中不支持SSID VLAN，因为 C200P 不支持 VLAN 或 VLAN 接口。

注： C200P未来将通过固件升级支持VLAN和VLAN接口。届时，即使交换机本身不支持VLAN，也可以在上述拓扑1和拓扑2中支持SSID VLAN。

2. AP控制器模式

在此模式下，C200P 仅作为 AP 控制器，管理 AP 配置和强制门户认证数据。

它支持≤200 个 AP ，客户端设备数量仅受网关或交换机容量的限制。

拓扑结构：互联网 - 路由器 - 交换机 - AP 和 C200P

  • 设置要求：
    • 将调制解调器连接到路由器，将路由器连接到交换机，再将 C200P 和 AP 都连接到交换机。
    • 将C200P切换至AP控制器模式：
      • 登录C200P网页界面。
      • 进入快速设置并选择AP 控制器模式。
    • 确保 C200P 和 AP 处于同一 VLAN中，因为 AP 管理流量不携带 VLAN 标签。
  • SSID VLAN 支持：
    • 要启用 SSID VLAN，网关或交换机必须支持 VLAN、VLAN 接口和 DHCP 服务器，以便为 SSID VLAN 中的无线客户端分配 IP 地址。

如需进一步帮助，请联系我们的支持团队：support@cudy.com。

返回博客

53 条评论

Hello Cudy Support,

I am using a Cudy AX1500 router. I am experiencing two problems:

1. The internet speed (Mbps) is lower than expected.
2. The Wi-Fi coverage/range is also quite low.

Could you please tell me why this is happening and what settings I should use to get better speed and wider Wi-Fi coverage?

Please help me troubleshoot this issue.

Thank you.

Sk SINHA

@Dear Tilde.
OK. I see. We will provide your feedback to the product department for evaluation.

“Dear Cudy Support,

“For now, C200P has already support OpenWrt firmware” [Cudy Support] … well, no, PoE drivers are missing in OpenWRT which demotes the C200P to a “common” router with 4 ethernet Ports – so, why would I buy a C200P then if there are so many to choose from. ;-) You should make a USP of it …

For sure, OpenWRT is harder to handle. But if users decide to flash and use OpenWRT, I’d presume they know they do – as done by myself, but I needed to restore stock firmware due to lack of PoE features."

support

Dear Cudy Support,

“For now, C200P has already support OpenWrt firmware” [Cudy Support] … well, no, PoE drivers are missing in OpenWRT which demotes the C200P to a “common” router with 4 ethernet Ports – so, why would I buy a C200P then if there are so many to choose from. ;-) You should make a USP of it …

For sure, OpenWRT is harder to handle. But if users decide to flash and use OpenWRT, I’d presume they know they do – as done by myself, but I needed to restore stock firmware due to lack of PoE features.

Tilde

@Dear Tilde,
Thank you for your kindly advice. For now, C200P has already support OpenWrt firmware. If you will, you can update the intermediate firmware for C200P and then update the OpenWrt firmware. OpenWrt firmware is not easy to use system for normal user. We need to some more work to make it easy to use.

“Dear Cudy Support,

I seriously don’t get why you are reinventing the wheel. Why don’t you just publish an OpenWRT Image with full driver support included so customers can flash C200P and have full access to all features, including VLAN and so on? Your firmware is even based on OpenWRT, so it would be easiest?"

support

Dear Cudy Support,

I seriously don’t get why you are reinventing the wheel. Why don’t you just publish an OpenWRT Image with full driver support included so customers can flash C200P and have full access to all features, including VLAN and so on? Your firmware is even based on OpenWRT, so it would be easiest?

Tilde

发表评论