Имя (SSID) и пароль сети Wi-Fi, а также параметры безопасности настроены по умолчанию. Имя (SSID) и пароль сети Wi-Fi указаны на этикетке на корпусе устройства.
Шаг 1. Введите в адресной строке браузера http://cudy.net или http://192.168.10.1. В качестве пароля для входа используйте слово «admin».
Шаг 2. Перейдите в раздел Общие настройки 🡢 Wi-Fi.
Smart Connect
Функция Smart Connect позволяет объединить диапазоны 2,4 ГГц и 5 ГГц в единую сеть с одним именем (SSID) и паролем.
Wi-Fi (2,4 ГГц, 5 ГГц)
Переключатели «Wi-Fi 2,4 ГГц» и «Wi-Fi 5 ГГц» позволяют включить (отключить) сеть Wi-Fi на диапазоне 2,4 ГГц и (или) 5 ГГц, соответственно.
Имя (SSID) и пароль сети Wi-Fi
Укажите имя и пароль сети Wi-Fi в полях «SSID» и «Пароль».
Примечание. Если настройки Wi-Fi изменялись через Wi-Fi, то после сохранения изменений устройство, через которое выполнялись изменения, будет отключено от сети Wi-Fi.
Шифрование
Доступны следующие опции: «Нет шифрования», «WPA-PSK», «WPA2-PSK», «WPA-PSK/WPA2-PSK» (рекомендуемый параметр), «WPA2-PSK/WPA3-SAE», «WPA3-SAE».
Примечание. Не рекомендуется вносить изменения в этот параметр.
Режим
2,4 ГГц: 802.11b, 802.11b/g, 802.11b/g/n, 802.11b/g/n/ax.
5 ГГц: 802.11a, 802.11a/n, 802.11a/n/ac, 802.11a/n/ac/ax.
Канал
По умолчанию используется значение «Авто». При необходимости выберите нужный параметр из выпадающего списка. Рекомендуется вносить изменения в этот параметр, только если наблюдаются проблемы с подключением из-за помех.
Ширина канала
По умолчанию используется значение «Авто». При необходимости выберите нужный параметр из выпадающего списка.
2,4 ГГц: 20 МГц или 40 МГц.
5 ГГц: 20 МГц, 40 МГц или 80 МГц.
Мощность передатчика
«Максимальная», «Средняя» или «Минимальная».
По умолчанию используется значение «Максимальная».
Примечание. Не рекомендуется вносить изменения в этот параметр.
Скрытый SSID
Этот параметр позволит скрыть SSID из списка сетей Wi-Fi. Чтобы подключиться к скрытой сети, нужно вручную ввести параметры сети.
Комментариев: 90
@Hein de Lange
Without support for 802.11r, a mesh network will never work properly.
Hi,
I’d like to report that the WR3600 mesh functionality is worse than having a group of APs in standalone mode. My two are connected via cable.
There is no benefit in having my two WR3600s meshed apart from just the config being applied to both units.
Drawbacks:
The biggest issue is that the two WR3600s keep on choosing the same channel. My IOT devices on 2.4GHz kept on dropping connection, perhaps because all of them are talking on the same band. This is silly. I’ve raised this before, but Cudy have not yet been able to fix this. Breaking my mesh into standalone units has resulted in a much better wireless experience for me. My device now all connect happily.
I can’t see from my main unit to which band a device connects to on another unit. After having two separate instances, I could see that some devices were connected to a band I didn’t want and I could correct this. This was not visible when in mesh mode.
Local latency, I.E. from my phone to default gateway also dropped from 70ms (Mesh) to about 6ms (standalone). This is while being about 7m away from my AP. No other change was made apart from going standalone.
I hope this helps someone else as I was about to replace my WR3600s. My experience is now much improved.
@Support
The issue is that when I configure the device to WPA2-only mode, the obsolete WPA1 protocol remains active. I have reported this multiple times, and you have stated it is not happening. However, my testing confirms it is. This situation suggests either a critical bug in the firmware or a lack of technical understanding of the issue on your support team. Please investigate this seriously
@Dear MN,
I see the picture. I think it doesn’t matter. We have removed the TKIP. So for now, is there any problem when connecting to this Wi-Fi?
“@Support
WR3600-R77-2.3.15Beta-20251027-094952-sysupgrade
WPA2-PSK only, WPA is still active
https://i.postimg.cc/6qFM0wzb/Screenshot-20260210-154034-Wi-Fi-Analyzer.jpg
https://github.com/VREMSoftwareDevelopment/WiFiAnalyzer"
@Support
WR3600-R77-2.3.15Beta-20251027-094952-sysupgrade
WPA2-PSK only, WPA is still active
https://i.postimg.cc/6qFM0wzb/Screenshot-20260210-154034-Wi-Fi-Analyzer.jpg
https://github.com/VREMSoftwareDevelopment/WiFiAnalyzer