Шаг 1. Введите в адресной строке браузера http://cudy.net или http://192.168.10.1.
Шаг 2. Перейдите в раздел Общие настройки 🡢 VPN и переведите переключатель Включить в подразделе VPN во включённое положение.
Чтобы включить (отключить) VPN для конкретных устройств, перейдите в раздел Состояние системы 🡢 Устройства и переведите переключатель VPN напротив нужного устройства в нужное положение.
Шаг 3. В выпадающем списке параметра Протокол выберите нужный протокол и настройте параметры согласно указаниям поставщика VPN-услуг.
PPTP
Введите адрес VPN-сервера (например, 113.92.73.163), а также имя пользователя и пароль, предоставленные поставщиком VPN-услуг.
L2TP
Введите адрес VPN-сервера (например, 113.92.73.163), а также имя пользователя, пароль и ключ PSK, предоставленные поставщиком VPN-услуг.
Если поставщик VPN-услуг также предоставляет IP-адрес для привязки учётной записи, активируйте параметр Использовать пользовательский IP-адрес туннеля.
OpenVPN
Нажмите на кнопку Обзор... и импортируйте файл настроек, полученный от поставщика VPN-услуг.
WireGuard
Нажмите на кнопку Обзор... и импортируйте файл настроек, полученный от поставщика VPN-услуг.
Поля подразделов Интерфейс и Одноранговый узел будут заполнены автоматически с помощью файла настроек (CONF) поставщика VPN-услуг.
ZeroTier
Введите нужные значения в поля Идентификатор сети ZeroTier и Шлюз.
Комментариев: 196
@Meehow,
Dear Customer,
Thank you for contacting Cudy support team.
Our technical support has sent you the solutions via email. Please check.
“Last problem exists on p5 with the latest software available”
@Meehow,
Dear Customer,
Thank you for contacting Cudy support team.
Our technical support has contacted you via email. Please check.
“Hello, I have a problem with Wireguard site to site vpn. It’s connecting to destination router, however I cannot access local subnet from remote subnet. It’s working the other way. I also spotted that route 0.0.0.0/0 is injected to routing table despite the fact I only specified remote subnets as destination for vpn tunnel policy. What is the solution as I cannot access ssh and check and correct vpn settings manually?”
Last problem exists on p5 with the latest software available
Hello, I have a problem with Wireguard site to site vpn. It’s connecting to destination router, however I cannot access local subnet from remote subnet. It’s working the other way. I also spotted that route 0.0.0.0/0 is injected to routing table despite the fact I only specified remote subnets as destination for vpn tunnel policy. What is the solution as I cannot access ssh and check and correct vpn settings manually?
@Vit,
Dear Customer,
Thank you for contacting Cudy support team.
Our technical support has contacted you via email. Please check.
“hello!
wr3000h vpn settings work incorrectly. when i setup openvpn or wireguard clients some settings don’t work. don’t work the most important setting – VPN Policy (Domain). Rule Allow listed only Domains doesn’t work.
maybe you have new firmware or some solution.
Thanks.
| HW: WR3000H V1.0 | FW: 2.2.7-20240906-085755 |”