O sistema Mesh Cudy Whole Home foi desenvolvido para eliminar zonas mortas e fornecer Wi-Fi ininterrupto em toda a sua casa. Este artigo orientará você na construção de um sistema Mesh passo a passo.
Preparação:
1. Certifique-se de possuir pelo menos 2 produtos Cudy.
2. Todos os produtos Cudy são compatíveis com a tecnologia mesh: Home Mesh-Site oficial da Cudy
3. O firmware está atualizado:Centro de downloads
4. Leve-os para a mesma sala durante a configuração.
5. Redefina todos os seus produtos Cudy para as configurações de fábrica. (Com o aparelho ligado, pressione e segure o botão RESET com um alfinete por 6 segundos e depois solte.)
6. Configure seu roteador principal e conecte-o à Internet.
Aqui tomamos M1800 e WR2100 como exemplos:
Passo 1: Abra um navegador da web e vá parahttp://cudy.netouhttp://192.168.10.1.
Para mais detalhes, consulteComo fazer login na interface web do Cudy Router?
Passo 2: Na página Status do Sistema, clique no botão "+".
Etapa 3: Pressione o botão WPS no M1800 e depois pressione o botão WPS no WR2100.
Unidade de malha principal: Flash branco
Unidade de malha adicional: pisca em branco e vermelho alternadamente
Passo 4:Irá para "Digitalização", então "Conectando".
Passo 5: Aguarde até que o LED do sistema do roteador complementar fique azul sólido e, em seguida, reposicione o WR2100.
Passo 6: Sucesso e aproveite a rede mesh.
Observação:
1. O roteador 4/5G só pode ser configurado como uma unidade mesh principal. Por exemplo:
2. Você não conseguirá acessar a interface web do roteador mesh adicional. Se desejar alterar as configurações, clique em "Status do sistema"->"Malha".
71 comentários
@Dear Gabriel,
Basically, this is a hardware issue. May be caused by the cable or the router. We can have a compare test. You can choose one of the other two routers, Reset it and set it to be the main mesh router and connect to the same cable to check if it work on 1 Gbps or 100Mbps to judge the root cause.
“Dear Cudy Support,
I recently purchased a Cudy AX3000 Gigabit WiFi 6 Mesh Router along with two additional AX3000 mesh units, all of which support gigabit Ethernet ports.
My internet plan provides 200Mbps, and I am using undamaged Cat 6 Ethernet cables. The main router is connected to one of the mesh nodes via Ethernet. Up until yesterday, everything was working perfectly—I was getting full gigabit speeds through the LAN ports.
However, after rebooting the entire system today, the main router’s Ethernet ports are now only delivering 100Mbps. I’ve confirmed that the cables are properly seated and not damaged, and the same setup was previously delivering full gigabit speeds without issue.
Could you assist in identifying what might have caused this and how to resolve it?
Thank you"
Dear Cudy Support,
I recently purchased a Cudy AX3000 Gigabit WiFi 6 Mesh Router along with two additional AX3000 mesh units, all of which support gigabit Ethernet ports.
My internet plan provides 200Mbps, and I am using undamaged Cat 6 Ethernet cables. The main router is connected to one of the mesh nodes via Ethernet. Up until yesterday, everything was working perfectly—I was getting full gigabit speeds through the LAN ports.
However, after rebooting the entire system today, the main router’s Ethernet ports are now only delivering 100Mbps. I’ve confirmed that the cables are properly seated and not damaged, and the same setup was previously delivering full gigabit speeds without issue.
Could you assist in identifying what might have caused this and how to resolve it?
Thank you
@Dear Walter,
Yes, you can. The Cudy APs, such as the AP3000 and AP1300 can work as the main mesh device to manage other APs. You can set up one of the AP3000 and connect it to the network. Then connect other AP to the network. The mesh system will be installed automatically.
“Can I set up a mesh network using only Cudy AP’s? I have a different brand router so I want to build a mesh network with just the AP’s”
Can I set up a mesh network using only Cudy AP’s? I have a different brand router so I want to build a mesh network with just the AP’s
@Dear Carlos,
Our technical support has sent you the firmware of WR6500 via email. Please check.
“Hello, I have a BE3600 and a BE 6500 but i cant connect them with mesh, be3600 has the firmware updated but 6500 doesnt”