Avisos
Esta página lista softwares de dispositivos compatíveis com o sistema OpenWrt. Antes de baixar e instalar o software, observe que o Projeto OpenWrt é um sistema operacional Linux voltado para dispositivos embarcados. Em vez de tentar criar um firmware único e estático, o OpenWrt oferece um sistema de arquivos totalmente gravável com gerenciamento de pacotes. Isso o libera da seleção e configuração de aplicativos fornecidas pelo fornecedor e permite que você personalize o dispositivo por meio do uso de pacotes para se adequar a qualquer aplicação. Para desenvolvedores, o OpenWrt é a estrutura para construir um aplicativo sem a necessidade de construir um firmware completo em torno dele; para usuários, isso significa a capacidade de personalização completa, para usar o dispositivo de maneiras nunca antes imaginadas.
Descrição
- Este arquivo só pode ser usado quando o seu roteador funciona na interface web do Cudy.
- Se o roteador já estiver funcionando com a interface OpenWRT, o usuário deverá restaurá-lo para o firmware oficial da Cudy primeiro. Em seguida, atualizar o roteador com este firmware.
- Como restaurar o roteador para o firmware oficial da Cudy? Leia o arquivo leia-me no arquivo baixado.
Garantia:
Cudy declara por meio deste
- Nós, da Cudy, não oferecemos garantia para nenhum software que não seja lançado pela Shenzhen Cudy Technology Co., Ltd.
- Não assumimos nenhuma garantia para produtos que tenham instalado qualquer software não lançado pela Shenzhen Cudy Technology Co., Ltd.
- Se você precisar usar o software openwrt, sugerimos que você o baixe do site oficial da Cudy.
Baixe o firmware OpenWrt para remover a verificação de assinatura:Dirigir
Localizador de firmware OpenWrt (não lançado pela Cudy):Seletor de Firmware OpenWrt
1530 comentários
Hello.
I have a Cudy WR3000 V1.0 router.
Serial number starts with: 2532
Current stock firmware: 2.4.19-20250828-192837
I would like to install official OpenWrt.
Please send me the latest Cudy-signed OpenWrt intermediate firmware compatible with my WR3000 V1.0 and this hardware/flash revision.
Thank you.
Hello,
I have a Cudy WR3000 V1.0 EU router.
Serial number starts with: 2539
Current stock firmware: 2.4.19-20250828-192837
I would like to install official OpenWrt.
Please send me the latest Cudy-signed OpenWrt intermediate firmware compatible with my WR3000 V1.0 and this hardware revision.
Thank you.
Greetings,
I would like to request for the signed openwrt firmware for M3000 with a Motorcomm YT8821 (Variant 2) please.
Thanks
@Dear Mike,
The firmware file in Google Drive is correct. This is for both hardware version. Please unzip the file before update.
Note: If you have installed Mesh system with the router. You can’t update the firmware. Please power off the other Mesh device. Then reset this router to factory default. You can update this firmware before mesh system installed.
“Hi,
I would also like to request the M3000 V.2 with the Motorcomm YT8821 chip, if that’s possible.
Thank you.”
@Dear Горбунов Михаил,
I think there is some hardware faulty in the router. You can try to contact the seller to request a replacement and try again.
“Hello. I specifically need to install OpenWrt on a Cudy M3000 V2.0. The current issue is not simply with the stock firmware, but with the OpenWrt installation process and the intermediate firmware file.
The situation is as follows:
Router: Cudy M3000 V2.0
I used the intermediate firmware file intended for transitioning from the stock Cudy firmware to OpenWrt.
After flashing that intermediate file, the router does not boot into OpenWrt correctly.
The Ethernet connection periodically goes down and comes back up.
The router appears to enter a reboot/boot loop, with the LED changing states.
There is no stable access to OpenWrt at 192.168.1.1.
Sometimes 192.168.10.1 becomes available again.
So my goal is not just to restore the stock firmware. I need to successfully complete the installation of OpenWrt.
Could you please clarify:
After flashing your intermediate file, should the M3000 V2.0 boot directly into OpenWrt?
If yes, why might my router be entering a boot loop instead of booting OpenWrt?
Is another firmware file required after the intermediate file?
If so, which exact OpenWrt image should be used for Cudy M3000 V2.0?
Should it be a factory.bin, sysupgrade.bin, or a special recovery/install image?
If the next step must be performed via TFTP, please provide the exact procedure:
required filename;
PC IP address;
router IP address;
which LAN port to use;
RESET/power-on sequence;
which firmware image should be transferred.
Could this problem be caused by the intermediate firmware itself or by a specific hardware revision of the M3000 V2.0?
What I need is a working step-by-step procedure for installing OpenWrt on the M3000 V2.0 from its current state, because at the moment the intermediate firmware does not result in a successful OpenWrt boot.
If necessary, I can provide a video of the boot loop, ipconfig/ping output, and the current stock firmware version."