WISP režīms:
WISP režīmā maršrutētājs ļauj vairākiem lietotājiem koplietot WISP interneta savienojumu. Šādā veidā LAN pieslēgvietas ierīces koplieto vienu un to pašu IP no WISP, izmantojot bezvadu pieslēgvietu. Kad bezvadu ports ir savienots ar WISP, tas darbojas kā WAN ports.
Bieža tīkla topoloģija:
1.solis: Atveriet tīmekļa pārlūkprogrammu un dodieties uz http://cudy.net vai http://192.168.10.1.
Sīkāku informāciju skatīt Kā pieteikties Cudy maršrutētāja tīmekļa saskarnē?
2. solis: Atvērsies ātrās iestatīšanas logs, izvēlieties "WISP", pēc tam dodieties uz "Nākamais".
3. solis: Izvēlieties savu "Laika joslu".
4. solis: Izvēlieties saimniekdatora tīklu, kuru vēlaties paplašināt. Noklikšķiniet uz "Pieslēgt".
Vai noklikšķiniet uz Vispārējie iestatījumi->WISP->Atļaut un pēc tam izvēlieties saimniekdatoru tīklu, kuru vēlaties paplašināt.
5. solis: Iesniedziet uzņēmēja tīkla bezvadu paroli.
Piezīme: Pārliecinieties, ka ievadītā bezvadu tīkla parole ir pareiza, pretējā gadījumā konfigurācija nevar izdoties.
6. solis: Pielāgojiet bezvadu tīkla nosaukumu un paroli vai saglabājiet tos pēc noklusējuma.
7. solis: Spiediet "Save &; Apply", lai pabeigtu konfigurāciju.
8. posms: No sistēmas pārstartēšanas pagaidiet dažas sekundes, kad atkal parādīsies pieteikšanās lapa, un varat baudīt internetu.
114 comments
Hello Cudy Support. Could I also get please the beta version of Firmware supporting WISP work mode for the WR6500H router?
Thx
@Dear Peter Tomaščík,
Our technical support has sent you the firmware via email. Please check.
“I recently purchased the Cudy WR6500 as an upgrade to my older Cudy WR3000. My original plan was to use the new WR6500 as my main router and repurpose the WR3000 as a Mesh node to extend my network coverage.
However, I ran into a major issue: the WISP mode is missing in the WR6500 settings, whereas it works perfectly fine on the older WR3000.
Because the WR6500 lacks WISP support, I am currently forced to use it only as a Mesh extension instead of the main router, which completely degrades its performance and defeats the purpose of the upgrade.
Could the support team or anyone here provide me with a firmware version for the WR6500 that includes the WISP functionality?”
@Dear Lawson,
Please go to “General Settings” —"WISP " function page to set it up.
“I have the 4GvLTE N300 V3.0
I’ve got firmware 2.5.12 installed, but still no WISP
Could you send me the firmware that allows for Wisp please. I’m happy to test it if it’s Beta.”
@Dear John,
I think yes. WR1200 supports WISP function to connect the main Wi-Fi via wireless. But you must check if the signal strength starlink mini wifi router at the placement of WR1200 is powerful enough to connect to?
“Hi, can I use the wr1200 to feed wired internet into my lan from a starlink mini wifi router. I would like to not have a wire from the starlink into my existing lan which covers 4 floors of a concrete building. Is this compatible.
Thank you.”
I recently purchased the Cudy WR6500 as an upgrade to my older Cudy WR3000. My original plan was to use the new WR6500 as my main router and repurpose the WR3000 as a Mesh node to extend my network coverage.
However, I ran into a major issue: the WISP mode is missing in the WR6500 settings, whereas it works perfectly fine on the older WR3000.
Because the WR6500 lacks WISP support, I am currently forced to use it only as a Mesh extension instead of the main router, which completely degrades its performance and defeats the purpose of the upgrade.
Could the support team or anyone here provide me with a firmware version for the WR6500 that includes the WISP functionality?