מצבי הפעלה וטופולוגיות של C200P

ה-C200P הוא התקן רשת רב-תכליתי המשלב פונקציונליות של נתב ובקר AP, ומציע שני מצבי פעולה:נתב ראשי ובקר AP(ברירת מחדל) ובקר APהוראה זו מספקת הוראות התקנה והמלצות לטופולוגיית רשת לביצועים אופטימליים.

1. נתב ראשי ובקר AP (ברירת מחדל)

במצב זה, ה-C200P מתפקד גם כנתב וגם כבקר AP.
מומלץ לנהל≤10 נקודות גישהו≤100 לקוחות.

טופולוגיה 1: אינטרנט - C200P - מתג - נקודות גישה

  • מקרה שימושמתאים לניהול מספר נקודות גישה (דורש מתג להרחבת קיבולת הפורטים).
  • דרישות התקנה:
    • חבר את המודם ליציאת ה-WAN של C200P, את יציאת ה-LAN של C200P למתג, ואת נקודות הגישה למתג.
    • ודא שה-C200P וה-AP נמצאים במצבאותו VLAN, מכיוון שתעבורת ניהול AP אינה נושאת תגי VLAN.
  • תמיכה ב-VLAN של SSID:
    • הפעלת SSID VLAN תגרום לנתוני הלקוח לשאת תג VLAN כאשר הם נשלחים מ-AP.
    • ה-C200P אינו תומך ברשתות VLAN או ממשקי VLAN.
    • כדי להפעיל רשתות VLAN של SSID, על המתג לתמוך ברשתות VLAN, ממשקי VLAN ושרתי DHCP כדי להקצות כתובות IP ללקוחות אלחוטיים ברשת VLAN של SSID.

טופולוגיה 2: אינטרנט - C200P - נקודות גישה

  • מקרה שימוש:מתאים לרשתות קטנות עם≤4 נקודות גישה(מוגבל על ידי 4 יציאות ה-LAN של ה-C200P).
  • דרישות התקנה:
    • חבר את המודם ליציאת ה-WAN של C200P ואת נקודות ה-AP ישירות ליציאות ה-LAN של C200P.
    • ה-C200P, נקודות הגישה ולקוחות האלחוטיים פועלים ב-אותה רשת.
  • תמיכה ב-VLAN של SSID:
    • רשתות VLAN של SSID הןלא נתמךבטופולוגיה זו, מכיוון שה-C200P אינו תומך ב-VLAN או ממשקי VLAN.

פֶּתֶק:ה-C200P יתמוך ב-VLAN ובממשק VLAN באמצעות שדרוג קושחה בעתיד. בשלב זה, ניתן יהיה לתמוך ב-SSID VLAN בטופולוגיות 1 ו-2 הנ"ל מבלי שהמתג יתמוך ב-VLAN.

2. מצב בקר AP

במצב זה, ה-C200P מתפקד אך ורק כבקר AP, ומנהל את תצורת AP ואת נתוני האימות של Captive Portal.

זה תומך≤200 נקודות גישה, כאשר מספר התקני הלקוח מוגבל רק על ידי קיבולת השער או המתג.

טופולוגיה: אינטרנט - נתב - מתג - נקודות גישה ו-C200P

  • דרישות התקנה:
    • חבר את המודם לנתב, את הנתב לסוויץ', ואת ה-C200P ואת נקודות הגישה לסוויץ'.
    • שנה את ה-C200P למצב בקר AP:
      • התחבר לממשק האינטרנט של C200P.
      • נווט אלהתקנה מהירהובחרבקר APמצב.
    • ודא שה-C200P וה-AP נמצאים במצבאותו VLAN, מכיוון שתעבורת ניהול AP אינה נושאת תגי VLAN.
  • תמיכה ב-VLAN של SSID:
    • כדי להפעיל רשתות VLAN של SSID, השער או המתג חייבים לתמוך ברשתות VLAN, ממשקי VLAN ושרתי DHCP כדי להקצות כתובות IP ללקוחות אלחוטיים ברשת VLAN של SSID.

לסיוע נוסף, צרו קשר עם צוות התמיכה שלנו בכתובת support@cudy.com.

Back to blog

39 comments

@Dear Tilde,
I am not sure about the time now.

“Dear Cudy Support,

“The C200P will support VLAN and VLAN interface through firmware upgrade in the future.”

When do you have a firmware upgrade scheduled to provide VLANs natively on C200P?

Kind regards"

Support

Dear Cudy Support,

“The C200P will support VLAN and VLAN interface through firmware upgrade in the future.”

When do you have a firmware upgrade scheduled to provide VLANs natively on C200P?

Kind regards

Tilde

@Dear Klaus,
Is it LT700 Outdoor or LT700? If it is LT700. Both of the LAN and WAN ports don’t support PoE function.
In addition, do you plan to connect the wired broadband line to the C200P? I don’t under stand well what do you plan to install the network. Do you plan to use the 4G connection as the main internet line or just a backup line?

“Dear Cudy Support Team,
I recently purchased three AP3000 units, one LT700, and one C200P, and I would like to operate these devices together.
My plan is to power the AP3000 access points as well as the LT700 through the PoE ports of the C200P.
However, the LT700 obtains its internet connection via 4G and therefore cannot be operated through a regular LAN port. The WAN port of the LT700 unfortunately does not support PoE.
Therefore, my questions are:
Can PoE be supplied to the LT700’s WAN port, or is this port fundamentally not PoE-capable?
Is there any way to operate the LT700 via one of the LAN ports, even though it receives its internet connection via 4G, so that it can be powered via PoE?
Thank you in advance for your assistance.
Kind regards,
Klaus”

Support

Dear Cudy Support Team,
I recently purchased three AP3000 units, one LT700, and one C200P, and I would like to operate these devices together.
My plan is to power the AP3000 access points as well as the LT700 through the PoE ports of the C200P.
However, the LT700 obtains its internet connection via 4G and therefore cannot be operated through a regular LAN port. The WAN port of the LT700 unfortunately does not support PoE.
Therefore, my questions are:
Can PoE be supplied to the LT700’s WAN port, or is this port fundamentally not PoE-capable?
Is there any way to operate the LT700 via one of the LAN ports, even though it receives its internet connection via 4G, so that it can be powered via PoE?

Thank you in advance for your assistance.
Kind regards,
Klaus

Klaus Proppe

@
Caro Fabio.
C200P non supporta la funzione di gestione dell’app Cudy. Non è possibile gestire il controller dall’app.
Di quante porte Ethernet hai bisogno sullo switch?
“Grazie per la risposta.
Per quanto riguarda l app cudy non c e nessun modo per gestire il controller dall app?
Anche che tipo di switch cudy layer 3 vlan gestito mi suggerisci da inserire nella mia rete?
Grazie di nuovo”

Support

Leave a comment