Hoiatused
See veebileht loetleb OpenWrt süsteemi toetavate seadmete tarkvara, enne tarkvara allalaadimist ja paigaldamist palume arvestada, et OpenWrt Project on Linuxi operatsioonisüsteem, mis on suunatud manussüsteemidele. Selle asemel, et püüda luua üksikut staatilist püsivara, pakub OpenWrt täielikult kirjutatavat failisüsteemi koos paketihaldusega. See vabastab teid müüja poolt pakutavate rakenduste valikust ja konfiguratsioonist ning võimaldab teil kohandada seadet pakettide abil mis tahes rakendusele sobivaks. Arendajate jaoks on OpenWrt raamistik, mille abil saab luua rakenduse, ilma et oleks vaja ehitada selle ümber täielikku püsivara; kasutajate jaoks tähendab see võimalust täielikuks kohandamiseks, et kasutada seadet viisil, mida nad pole kunagi ette kujutanud.
Kirjeldus
- Seda faili saab kasutada ainult siis, kui teie ruuter töötab Cudy veebi kasutajaliidese all.
- Kui ruuter juba töötab OpenWRT UI all, peaks kasutaja esmalt taastama selle Cudy ametliku firmware'ile. Ja seejärel uuendada ruuterit selle püsivara abil.
- Kuidas taastada ruuter Cudy ametlikule püsivara? Palun lugege alla laaditud faili readme.
Garantii:
Cudy deklareerib käesolevaga
- Me, Cudy, ei võta garantiid ühegi tarkvara eest, mida ei ole välja andnud Shenzhen Cudy Technology Co., Ltd. .
- Me ei võta garantiid toodete eest, millele on paigaldatud tarkvara, mida ei ole välja andnud Shenzhen Cudy Technology Co., Ltd. .
- Kui teil on vaja kasutada openwrt tarkvara, soovitame selle alla laadida Cudy ametlikust veebisaidist.
Laadige alla OpenWrt püsivara, et eemaldada allkirja kontroll: Ajama
OpenWrt Firmware Finder (ei ole Cudy poolt välja antud): OpenWrt Firmware Selector
1319 comments
@Dear araujorm,
Our technical support has sent you the firmware via email. Please check.
“Hi. It’s been a few weeks since I’ve sent Cudy via email a Openwrt image that should be suitable for RE1800 V2, and also shared the link to the github repository for it, asking if you could sign it so that I can finish providing support for it along with the Opewrt team. After an initial reply asking to wait, I got no other replies. Could you please take a look into it?”
@Dear Viktor (tg: OriginWave),
Our technical support has sent you the firmware via email. Please check.
“Hello Cudy Support Team,
I have a Cudy WR3000 v1.0 router.
Serial Number starts with 2549
I would like to install OpenWrt on my router. Could you please provide the Cudy-signed intermediate firmware compatible with my hardware revision?
Thank you.”
@Уважаемая Никита,
Прошивки OpenWrt для WR1300 v4 не существует.
“Здравствуйте, поддерживает ли Cudy WR1300 v4 OpenWrt? Я нашел промежуточную прошивку на гугл диске для v4, но не нашел прошивку OpenWrt для v4.”
@Dear Lukas,
Our technical support has contacted you via email. Please check.
“Hello,
I have a Cudy WR3000 v1.0 router.
Serial number starts with: 2517
Current stock firmware: 2.4.19-20250828-192837
I downloaded the package:
“WR3000+V1 without recovery TFTP”
However, the package only contains:
- openwrt-mediatek-filogic-cudy_wr3000-v1-sysupgrade.bin
The stock Cudy firmware rejects this file with an error during firmware upgrade.
From the OpenWrt installation instructions, it seems that a signed intermediate firmware or factory image is required before installing OpenWrt.
Could you please provide the correct intermediate firmware for WR3000 v1.0 compatible with the latest stock firmware?
Thank you."
@Dear Leo,
We don’t change the Flash chip on WR3000 1.0. Please just use the intermediate firmware “WR3000 v1 without recovery TFTP” .
“Hello!
Device: Cudy WR3000 v1.0
Serial Number: 2553…
Stock firmware version: 2.4.19-20250828-192837
The publicly available intermediate firmware in your Google Drive folder
“WR3000 v1 without recovery TFTP” is incompatible with the new F50L1G41LC
flash chip used in units manufactured from week 43 of 2025 onward.
Could you please email me the updated Cudy-signed intermediate firmware
for the WR3000 v1.0 with the new flash chip?
Thank you!"