Hoiatused
See veebileht loetleb OpenWrt süsteemi toetavate seadmete tarkvara, enne tarkvara allalaadimist ja paigaldamist palume arvestada, et OpenWrt Project on Linuxi operatsioonisüsteem, mis on suunatud manussüsteemidele. Selle asemel, et püüda luua üksikut staatilist püsivara, pakub OpenWrt täielikult kirjutatavat failisüsteemi koos paketihaldusega. See vabastab teid müüja poolt pakutavate rakenduste valikust ja konfiguratsioonist ning võimaldab teil kohandada seadet pakettide abil mis tahes rakendusele sobivaks. Arendajate jaoks on OpenWrt raamistik, mille abil saab luua rakenduse, ilma et oleks vaja ehitada selle ümber täielikku püsivara; kasutajate jaoks tähendab see võimalust täielikuks kohandamiseks, et kasutada seadet viisil, mida nad pole kunagi ette kujutanud.
Kirjeldus
- Seda faili saab kasutada ainult siis, kui teie ruuter töötab Cudy veebi kasutajaliidese all.
- Kui ruuter juba töötab OpenWRT UI all, peaks kasutaja esmalt taastama selle Cudy ametliku firmware'ile. Ja seejärel uuendada ruuterit selle püsivara abil.
- Kuidas taastada ruuter Cudy ametlikule püsivara? Palun lugege alla laaditud faili readme.
Garantii:
Cudy deklareerib käesolevaga
- Me, Cudy, ei võta garantiid ühegi tarkvara eest, mida ei ole välja andnud Shenzhen Cudy Technology Co., Ltd. .
- Me ei võta garantiid toodete eest, millele on paigaldatud tarkvara, mida ei ole välja andnud Shenzhen Cudy Technology Co., Ltd. .
- Kui teil on vaja kasutada openwrt tarkvara, soovitame selle alla laadida Cudy ametlikust veebisaidist.
Laadige alla OpenWrt püsivara, et eemaldada allkirja kontroll: Ajama
OpenWrt Firmware Finder (ei ole Cudy poolt välja antud): OpenWrt Firmware Selector
1319 comments
@Dear Michael,
Regarding the tftpd recovering firmware method. You can refer to this article.
https://www.cudy.com/blogs/faq/how-to-recovery-the-cudy-router-from-openwrt-firmware-to-cudy-official-firmware?pos=1&_sid=b98054b19&ss=r
You can download the firmware for you router via this link.
https://www.cudy.com/pages/download-center/wr3000-1-0
“Hello Cudy Support Team ,
Maybe you have some intermediate , temporary firmware ,that I can flash to my WR3000 v1 using tftp64 so it will restore it’s state to defaults ? with memory erasing and rebuilidng the filesystem ? Thaks in advance.”
Hello Cudy Support Team ,
Maybe you have some intermediate , temporary firmware ,that I can flash to my WR3000 v1 using tftp64 so it will restore it’s state to defaults ? with memory erasing and rebuilidng the filesystem ? Thaks in advance.
“@Dear Michael,
I see. I suggest you can try to do it by yourself. We don’t have such instructions.
“Hi Cudy Support Team , I’ve tried what you suggested – flashing older official firmware, but no luck , my Cudy WR3000 v1 is still bootlooping. Is there any firmware or recovery steps that I might perform in order to recover my router so I be able to boot into GUI ?
One more note : after flashing your firmware from Google drive or OpenWRT firmware, I’m able to enter to OpenWRT failsafe mode and access router via LAN using SSH , but from there I wasn’t able to perform system restoration steps from OpenWRT guides( I just don’t know how to do it propertly) . Thanks is advice for your support.
@Dear Support
I have already built a working OpenWrt firmware for AP1300 v1.0, based on the OpenWrt firmware for AP1300 Outdoor v1.0 (same SoC and hardware platform).
The firmware itself builds and boots, but I cannot flash it via TFTP or the web interface because the stock firmware requires a signed image.
To proceed without hardware modification (UART/SPI), I need an intermediate firmware that can be installed via the web interface and allows upgrading to a custom OpenWrt image (without signature verification).
Could you please provide such an intermediate firmware for AP1300 v1.0, or advise if there is an official way to bypass the signature check for development purposes?
Thank you.
“@Dear Bourn,
There is no OpenWrt firmware for AP1300 V1.0 currently. The OpenWrt firmware is not developed by Cudy but by the developers. We need the OpenWrt forum official support the router at first, then we can release a middle firmware for you, then you can use and upgrade to the OpenWrt firmware. "
@Dear Michael,
I see. I suggest you can try to do it by yourself. We don’t have such instructions.
“Hi Cudy Support Team , I’ve tried what you suggested – flashing older official firmware, but no luck , my Cudy WR3000 v1 is still bootlooping. Is there any firmware or recovery steps that I might perform in order to recover my router so I be able to boot into GUI ?
One more note : after flashing your firmware from Google drive or OpenWRT firmware, I’m able to enter to OpenWRT failsafe mode and access router via LAN using SSH , but from there I wasn’t able to perform system restoration steps from OpenWRT guides( I just don’t know how to do it propertly) . Thanks is advice for your support.”
@Dear A,
Our technical support has contacted you via email. Please check.
“WR3000P2550 . Can’t change to intermdiate cudy_wr3000p-v1-sysupgrade_20251119.bin: “File is invalid. Please retry.”
is it possible to get openwrt for WR3000P with new serial number?”