Hoiatused
See veebileht loetleb OpenWrt süsteemi toetavate seadmete tarkvara, enne tarkvara allalaadimist ja paigaldamist palume arvestada, et OpenWrt Project on Linuxi operatsioonisüsteem, mis on suunatud manussüsteemidele. Selle asemel, et püüda luua üksikut staatilist püsivara, pakub OpenWrt täielikult kirjutatavat failisüsteemi koos paketihaldusega. See vabastab teid müüja poolt pakutavate rakenduste valikust ja konfiguratsioonist ning võimaldab teil kohandada seadet pakettide abil mis tahes rakendusele sobivaks. Arendajate jaoks on OpenWrt raamistik, mille abil saab luua rakenduse, ilma et oleks vaja ehitada selle ümber täielikku püsivara; kasutajate jaoks tähendab see võimalust täielikuks kohandamiseks, et kasutada seadet viisil, mida nad pole kunagi ette kujutanud.
Kirjeldus
- Seda faili saab kasutada ainult siis, kui teie ruuter töötab Cudy veebi kasutajaliidese all.
- Kui ruuter juba töötab OpenWRT UI all, peaks kasutaja esmalt taastama selle Cudy ametliku firmware'ile. Ja seejärel uuendada ruuterit selle püsivara abil.
- Kuidas taastada ruuter Cudy ametlikule püsivara? Palun lugege alla laaditud faili readme.
Garantii:
Cudy deklareerib käesolevaga
- Me, Cudy, ei võta garantiid ühegi tarkvara eest, mida ei ole välja andnud Shenzhen Cudy Technology Co., Ltd. .
- Me ei võta garantiid toodete eest, millele on paigaldatud tarkvara, mida ei ole välja andnud Shenzhen Cudy Technology Co., Ltd. .
- Kui teil on vaja kasutada openwrt tarkvara, soovitame selle alla laadida Cudy ametlikust veebisaidist.
Laadige alla OpenWrt püsivara, et eemaldada allkirja kontroll: Ajama
OpenWrt Firmware Finder (ei ole Cudy poolt välja antud): OpenWrt Firmware Selector
1319 comments
@Dear Jaddie,
You can try to update back to older firmware first then try again. You can download the firmware 2.0.0 via the link.
https://www.cudy.com/en-us/pages/download-center/m3000-1-0
You can follow this instruction on the website to downgrade the firmware if you have installed mesh system with them.
https://www.cudy.com/en-us/blogs/faq/how-to-downgrade-the-firmware-to-the-older-version-of-mesh-system
Apologies, just checked and it actually just says the file is invalid, think the not applicable might have been when I was using openwrt’s file to see if it accepted it.
I am looking at trying to flash openwrt onto my cudy devices I have the M3000, one running
2.5.0-20260112-084313 and the other running 2.4.19-20250828-183718 it would be good to find out what is required to flash it onto them, as when I try it uploads the file initial file which I assume is meant to remove the signature checks, but it says the firmware is not applicable (presumably that firmware is out of date compared to what my devices already have on them) Is it possible to get an update version of the firmware to remove the sig check please?
@Dear Christian,
Our technical support has contacted you via email. Please check.
“I purchased six WR 3000 E for using them with OpenWRT. When I try to upload the cudy_wr3000e-v1-sysupgrade_20251119.bin from the Google Drive folder I get “Not applicable！Please upload the firmware applicable to the following models.”. The WR 3000 E is running 2.4.7 right now and the S/N is WR3000E24520. What am I doing wrong ? I really would like to run OpenWRT on the Cudys.”
I purchased six WR 3000 E for using them with OpenWRT. When I try to upload the cudy_wr3000e-v1-sysupgrade_20251119.bin from the Google Drive folder I get “Not applicable！Please upload the firmware applicable to the following models.”. The WR 3000 E is running 2.4.7 right now and the S/N is WR3000E24520. What am I doing wrong ? I really would like to run OpenWRT on the Cudys.